Shopping Cart

Your cart is empty.

Your cart is empty.

2Pcs TB6600 5A Stepper Motor Driver DC12-48V CNC Controller Nema 23 Nema17 Series Stepper Motor Single Axes 1 Phase Hybrid Metal Case CNC Engraving Machine

5.0 (2) Write Review
Free shipping on orders over $29.99

$29.99

$ 13 .99 $13.99

In Stock

1.:2pcs Tb6600 5a


About this item

  • HY-DIV268N-5A subdivision-type two-phase hybrid stepping motor drive using DC 12 ~ 48V power supply, suitable for drive
  • Two-phase hybrid stepping motor dynamic voltage 12 to 48V, the current is less than 5A outer diameter of 35 to 86 mm.
  • This drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth, almost no vibration and noise.
  • High-speed torque is much higher than other two-phase drive, high positioning accuracy.
  • Widely used in the engraving machine, CNC machine tools, packaging machinery and other high resolution requirements on the device.


Product Description

1

TB6600 5A Stepper Motor Metal Case and Metal Heatsink

  • Average current control, two-phase sinusoidal current drive output
  • DC 12 ~ 48V power supply, the internal integration of 12V and 5V regulator
  • Optically isolated signal input / output
  • Overvoltage, undervoltage, overcurrent, and white short-circuit protection
  • Input voltage DC 12 ~ 48V input
  • The input current of 1 to 5 amps, select the drive a stepper motor.
  • Output current of 0.2A ~ 5A
  • Temperature Operating Temperature -10 to 45 ℃; Storage temperature -40 ℃ to 70 ℃
  • Humidity not condensing, not drops
  • Gas prohibit combustible gas and conductive dust

  • Control signal interface:
  • 1, the definition of control signals
  • PUL +: step pulse signal is input side or the positive pulse signal input positive terminal
  • PUL-: the negative input of the negative input pulse signal or a positive pulse signal
  • DIR +: stepping direction signal input to the positive terminal or negative pulse signal input to the positive terminal
  • DIR -: stepping direction signal input of the negative side or reverse step pulse signal input negative terminal
  • EN +: offline can reset signal input side is
  • EN-: offline can reset signal input negative terminal
  • Offline enable signal is active, reset drive failure to prohibit any pulse, the output of the drive
  • Power component is turned off, the motor holding torque.
  • Control signal connections:
  • PC control signal can be high, also can be low effective. When active high, the control signal
  • The negative side together as a signal to active low, positive side of all control signals together as a signal common.
  • For example, open-collector and PNP output interface circuit diagram is as follows:
  • Input interface circuit (common cathode connection)
  • Note: the VCC is 5V, R short；
  • VCC value of 12V, R 1K, more than 1/8W resistor;
  • VCC value of 24V, R 2K, more than 1/8W resistor;

  • Function selection (DIP switch on the drive panel)
  • Set the motor per revolution steps
  • The drive to set the number of steps per motor revolution is 200 (whole step), 400 (2 segments), 1600 (8 segments), 3200 steps (16 segments).
  • The user can drive the front panel DIP switch SW3 is SW4 bit of the drive to set the number of steps (such as Table 1）：

  • Set the output phase current
  • To drive torque stepper motor, the user can drive panel DIP switch
  • SW1, SW2 is to set the drive output phase current (RMS) unit amperes, the switch position
  • Corresponding to the output current, output current value corresponding different types of drive.
  • The semi-flow functionality
  • The semi-flow function is a step pulse 200ms, the driver output current is automatically reduced to the rated output current50%, used to prevent motor heating.

  • The power interface
  • 1, DC +, DC-: to connect the drive power
  • DC +: DC power level, power supply voltage DC 12 to 48V. The maximum current is 5A.
  • The DC-: DC power supply negative level.
  • 2, A + A-B + B-: to connect the two-phase hybrid stepping motor
  • Drive and two-phase hybrid stepper motor's connection with the four-wire system, the motor windings in parallel and series connection, and connection method, high-speed performance, but the drive current is large (for motor winding current of 1.73 times), Connected in series when the drive current is equal to the motor winding current.
  • The installation
  • Around to have 20mm of space, can not be placed next to the other heating equipment, to avoid dust, oil mist, corrosive gases, high humidity is too big and strong vibration.
  • The status light indicates
  • RUN: green light in the normal work.
  • ERR: red light, power, light, power indicator

  • Package included:
  • 2 x Stepper motor driver

Sidney Clinkscales
Reviewed in the United States on February 17, 2025
CNC Stepper motor driver works very well, I had problems with the original drivers but these work great with no issues.
ARG
Reviewed in the United States on May 2, 2023
They're fine, but make a loud hissing noise on standby. It's incredibly annoying. Also no detailed datasheet.
Recommended Products
30amp DC Motor Forward Reverse Switch Toggle Switches 6 Pin 3 Position 9V 12V 24V 36V 48V AC 110V-220V

$5.99

$ 2 .99 $2.99

5.0
Select Option
DC 7-24V 200W Brushless dc Motor BLDC 3-Phase Brushless Motor Driver Hallless DC Motor Drive Board Speed Controller Module with Potentiometer,ESC Speed Controller

$13.99

$ 6 .99 $6.99

4.4
Select Option
Universal DC 12V/24V Motor Speed Controller,Motor Speed Regulator,Motor Governor Switch,Better Heat Dissipation,for Automobile Fan Heater, Defroster, Fans

$8.94

$ 4 .99 $4.99

4.6
Select Option
AC Motor Speed Controller Single Phase 110V/220V Vibration Motor Governor Supports Low Speed Start for 30W-120W Motor with Digital Display

$33.80

$ 14 .99 $14.99

4.9
Select Option
SparkFun Brushless Motor Driver - 3-Phase (TMC6300) Brushless Gimbal Motor, high-Side and Low-Side Control, 1.8V Regulated Power Output, Board Dimensions: (in) 0.80 x 0.60

$16.95

$ 7 .99 $7.99

4.7
Select Option
Franklin Electric - 2823028310 - FRANKLIN ELECTRIC Pump Control Panel: 3 hp Motor/Pump HP, 220V AC, 17, Deluxe CSCR

$536.35

$ 99 .00 $99.00

4.4
Select Option
SCHNEIDER Electric GV2-P08 / 2.5-4A Manual Motor Controller GV2-PO8 / 2.5-4A

$95.00

$ 39 .99 $39.99

5.0
Select Option
RS-1M-SH Relay & Controls | 1.5 hp - 2 hp Electric Motor Reversing Drum Switch - Spring Returned

$118.52

$ 53 .99 $53.99

4.3
Select Option