Your cart is empty.
Your cart is empty.49-22-1178 For Milwaukee T-Shank Metal/Wood Cutting Jig Saw Blade Assortment, 5-Pack
C. Ramsdale
Reviewed in the United States on March 31, 2025
As others have mentioned, these fit Milwaukee jig saws but are not Milwaukee brand. The only place that mentions Milwaukee is the webpage and the package has no mention of Milwaukee. I knew that when I ordered these for my Crafstman jig/scroll saw. I do prefer assortment packs over single blades but there isn’t much difference in these blades other than length and teeth count. They are all bi-metal and are not for heavy duty metal cutting and none are made of carbide or titanium. I have only used the larger tooth blade to cut some curves out of 2x6 boards and it cut about the same as the blades that came with the saw. If I have to cut through metal, I would reach for my oscillating blade tool with a titanium blade rather than my jig saw.If I could change anything about this assortment pack it would be to make at least one of the blades a 6-inch blade. I needed to cut a hole for a pvc pipe thru two 2x6 boards and the 4” blade was just not long enough because the 4” is the total length of the blade, but the cutting length is less than three inches. Also, if you shop around you can find a lot more blades in an assortment pack for this price point.
B. Coombs
Reviewed in the United States on March 30, 2025
These are a 5 blade assortment that fit perfectly into my jigsaw. I tried cutting some 1/4 inch maple plywood and these did cut very well. The cut was not as clean as I've seen with a sharp table saw blade but I have never seen a jig saw blade cut a perfectly clean cut. It did cut as clean as I have ever seen a jigsaw blade make a cut in plywood. Plywood is the hardest test for a jig saw. So these are very good.
Remington
Reviewed in the United States on March 28, 2025
I love my Leatherman. It's one of the best tools I've ever owned. Not that it's the absolute best at what job I'm doing, but that it's always on me, always available, that makes it so wonderful. My last Leatherman was a Wave and after twenty loyal years of service I left it sitting on the side of a vehicle at a junkyard, and it quickly grew legs. I ended up replacing it with a Surge, the Leatherman I've wanted for years. The Surge, unlike the Wave, has a t-shank adaptor to hold the saw and the file. I thought to myself "Could it accept jigsaw blades?" and so when I saw this listing I decided to find out.These blades arrived in the packaging shown on the listing and included the five promised blades.They fit! The little t-shank adaptor is the same and these fit right in. The longer ones are great, though are too long to close in the leatherman, but still very handy to have on hand. The smaller blades fit closed, so if you use one of these you can leave it in the Leatherman if you want. I love using these as opposed to the included Leatherman saw because these are much less expensive to replace if used hard or broken.Overall I'm very happy with these blades. They fit my Leatherman application just like I wanted and the smaller ones can even be left in rather than having to keep switching it out between uses. The longer ones may just get saved for the jigsaw.
Jeff B.
Reviewed in the United States on March 26, 2025
When I get jig saw blades, I am looking for strong blades that don’t bend and break easily and sharp teeth that last. For the teeth, it is always best to go with carbide for long life, but that is usually a higher price point. These Milwaukee jig saw blades are made of bi-metal and the cost isn’t that far off from carbide blades, so it may be more economical in the end to go ahead and get carbide blades. Still, for bi-metal blades these are definitely good quality. I have not had any problems with breakage or bending. I would describe these as a good workhorse set of blades that get the job done.
Customer
Reviewed in the United States on March 25, 2025
I decided to get some new blades to replace the Bosch blades I've used over the last few years and it's been harder than I expected. These blades are similar in that they are T blades and fit any jigsaw (mine is Black and decker) that uses a T blade, which is very common. While the cut was clean, it was not nearly as smooth as the older blade it was replacing, but it did cut the wood. Ultimately, this blade will get the job done but it's not a five-star blade.
Reviews
Reviewed in the United States on March 25, 2025
These blades have no TPI (teeth per inch) labeling. The blister card says there is a blade chart on the reverse side, but no such guide is printed there. Some of these blades have decently sharp teeth, while others have some sharp teeth and some dull. The shorter blades were clearly stamped out, so the set of the teeth is one-sided and the blade pulls hard to one side while cutting. There does not seem to have been much surface preparation before painting, aside from a basic cleaning. I think the main job of the paint is to hide how poorly some are made. At over $16 (at the time of this review), this set of blades is grossly overpriced.
Heidi
Reviewed in the United States on March 22, 2025
JODDMTTY T-Shank Jig Saw BladesFirst and foremost, these are Milwaukee-style T-shank blades, not actual Milwaukee brand blades. That said, they fit perfectly into T-shank and regular jig saws like Craftsman, DeWalt, and other common brands.This is a really handy variety pack to have in your toolbox for any cutting projects that might pop up unexpectedly. So far, I've used one of the blades, and it held up just fine—plenty of life left in it after a decent amount of work.Overall, they seem to be good quality, as they should be, considering the price point. They're about on par with, or maybe a couple of dollars more than, a Milwaukee variety pack at my local hardware store. Time will tell on durability, but so far, so good!
Country Life
Reviewed in the United States on April 3, 2025
These Milwaukee jig saw blades do a good job and they live up to the name brand. For bi-metal steel, they show good durability and the shafts are strong. They cut the wood cleanly and smoothly. The strong shafts give me good control without any bends or issues with the blades getting hung up and breaking. I do wish they had included more blades because it seems I always need more. The fit is great. My jig saw uses a T-shank, but it isn’t a Milwaukee. Still, these blades fit just fine. I am able to put them in the saw without any issues. I definitely recommend this set of jig saw blades. They are strong and reliable.
Recommended Products
$19.94
$ 8 .99 $8.99