Your cart is empty.
Your cart is empty.Safely remove gears, sprockets, bearings, bushings, pulleys, and flywheels with the ABN 3 Piece 3 Arm Gear Puller Pulley Extractor Tool Set. Steel construction ensures strength, durability, and longevity while cold-rolled, acme-threaded screw gives a smooth performance even under high stress. Inside and outside grip fits all your needs. 3 inch tool has 1.5 to 3-inch reach and a 4.5-inch jaw spread, 4 inch tool has 2.5 to 4 inch reach and a 6.25-inch jaw spread, and 6 inch tool has 4.75 to 6 inch reach and an 8.75-inch jaw spread. Even if you need to pull rusted bushing and bearings, the ABN Jaw Puller Bearing Separator Small Puller Tool Set will get the job done. Warning: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm.
anthony
Reviewed in the United States on June 17, 2024
The fact that you get 3 different sized pullers is awesome. These seem like they are built well, got me through my job, and now have a home in my tool box.
aardic
Reviewed in the United States on June 1, 2024
I don’t know what is the top brand but I understand the quality. Happy to have them.
P Koomen
Reviewed in Canada on November 26, 2023
The product is what is describe and off good quality, and would but again. if needed .
Kevin.V.Deveau.
Reviewed in Canada on January 8, 2022
The media could not be loaded.
Customer
Reviewed in Canada on February 23, 2021
Used to pull a diff seal after flipping the jaws, worked way better then drilling hole and using slide hammer. That’s all I have done either then so far but seem good
chuckiii3
Reviewed in the United States on October 14, 2021
I needed a set of gear pullers to remove a stubborn A/C compressor clutch on my vehicle, and this Set of 3 ABN 3-Jaw Gear Puller Set did the job with ease! The pullers are very well-constructed of forged hardened steel, and the jaws are reversible, so they can remove either inside or outside pulleys. Of special interest to me was that each of the three tools were adjustable for either short-reach or long-reach applications, making these gear pullers much more versatile than other brands. The jaws on these gear pullers are also slimmer, which allows access much tighter spaces than other brands. I am extremely satisfied with this Set of 3 ABN 3-Jaw Gear Puller Set, and I highly recommend these!
jsgdigital
Reviewed in Mexico on February 8, 2020
Me cobraron mucho de impuestos de importación
Sylvia
Reviewed in Canada on November 20, 2020
Product is ok. Did the job.
John Henry
Reviewed in the United States on September 27, 2019
This is a very useful set of three jaw pullers. Each puller has two jaw positions to allow the puller screw to be positioned as close as possible to the center shaft that it pulls against. The jaws may be set to grasp on the outside of a rim or between spokes against the inside of the rim. The price is very low for this set of pullers. A user should know that the short bolts that hold the jaws need to be tightened only finger tight and a couple of washers, a short piece of pipe or a properly sized socket should be placed on the shaft against which the puller screw is to be placed and tightened. Once pressure is exerted, a light hammer blow on the head of the screw should be dealt to start the pulled hub, gear, pulley, etc. on its journey off the shaft.
Danny J
Reviewed in the United States on January 19, 2019
I bought this set to remove a jaw coupler frozen to the drive shaft of an engine for a log splitter. After 10 years of use and some rust build up on the drive shaft the coupler would not budge a mm even after heating the piece and striking it from the backside with a hammer. I bought the set not knowing what size was going to be the correct size (turned out to be the 4") to do the job. It pulled the stuck part with little effort and no damage to either the tool or the drive shaft. This is a heavy duty, inexpensive tool which should satisfy the needs of most DIY'ers. I recommend the purchase of these gear pullers.
Customer
Reviewed in the United States on September 26, 2018
Needed a puller to pull the gear off of a pump. I didnt know what size I would need so I bought this set. It worked great first time out of the box. I will say the nuts and bolts were really loose but since it is a set that is somewhat adjustable the nuts being able to be swapped by hand not using a wrench is ok. I did add some locktite to the nuts so they would fall off when being moved around. I did get a small tool bag just for them as they are a specialty tool and should be kept separate until needed since most people wont be pulling gears or pulleys everyday. I do wish the end or the arms were a bit more tapered to fit in tighter areas but it still worked.
Buckeye Barbara
Reviewed in the United States on November 8, 2018
Used this to pull lower housing from winding assy on "Jet" brand model 700LL airator motor. Worked fine.As with any 3 (or 2) jaw puller, it works best with 2 people (men, women, or children); One holds the puller arms in place while the other tightens the main screw until the screw is snug & a wrench can be used.External finish of puller arms appears to be 'as forged', not polished. This is a cosmetic 'defect' and does not take away from the functionality of the puller.Main complaint is the nuts/bolts used to connect the arms to the 3-lobe central 'spider' are not equipped with lock nuts and are easy to come loose. I plan to replace these with elastic-style lock nuts. Wonder it they are English or metric--I guess I will find out.Over-all: pleased with what I got (all 3 sizes) for what I paid.Carl, Westerville OH
Customer
Reviewed in the United States on January 24, 2018
I get it, they are cheap so they are going to be built cheap. But even so I think they should be designed a bit better. All of the times I have went to use these I have ended up grabbing a posi lock or higher end puller instead. The spacing between the threaded plate, and the puller arms is not the same. This makes the puller arms very loose between the two metal brackets that hold it to the body and allows the arms slide oblong on the bearing or gear instead of staying spread evenly, then the puller will just fall off. I was able to fix this issue by installing washers between the puller arms and the pivot brackets to take up some slop. Another issue is that the hardware is very low grade, lock nuts should have been used. The first time I went to use one all 3 pullers had completely fallen apart just from bouncing around in my service truck tool box. Bottom line is I don’t think these are a very good value. It would be a different story if the thickness of the puller arms mounting holes was the same as the puller plate so there was no slop between the arms, and better hardware with lock nuts.
Recommended Products
