Your cart is empty.
Your cart is empty.This replacement power window motor and regulator assembly is precision-engineered and extensively tested to match the exact fit, function and performance of the stock window regulator on specific vehicle years, makes and models. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Ford Crown Victoria: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011] - [Mercury Grand Marquis: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011] - [Mercury Marauder: 2003, 2004]
Josh
Reviewed in the United States on June 15, 2024
It works like it should. It is a bit slower than the other 3 now but it still works fine. Install was not too bad, used 1/4x20 bolts and nylock nuts to attach window instead of provided rivets.
Alnadabi F
Reviewed in the United Arab Emirates on May 2, 2024
جيد
janice davis
Reviewed in the United States on May 13, 2024
Instal was easy. There are some good u-tube videos. Mine did come with a rivet pack. 5 to be exact. That will get the motor and regulator installed but no rivets for the window connection. Those rivets are 1/4 as well but much longer in depth. I had to order the Doorman rivet kit with it. I used the Pittsburgh 1/4 from HBor freight
W. Patton
Reviewed in the United States on October 24, 2024
Turned out great. Big job. Used bolts.
Maan B.
Reviewed in the United Arab Emirates on November 7, 2023
Wrong part. Dose not fit 2008 ford escapewill return
sedroray
Reviewed in the United States on November 3, 2023
It works! Its what you need for a Crown Vic! Its just not all you need. You need more pop rivets than the kit includes. The kit doesn't include a pop rivet gun, so get one that includes some 1/4 x 1/2" and 1/4 x 1" rivets. You need 2 1/4 x 1" rivets for the window, and a dozen 1/4 x 1/2" rivets for everything else. Once you have the rivets, the kit is perfect. It fits. Watch a YouTube video, and installation is a breeze. My driver's side window works now. I can go thru the drive-thru again. Just make sure you get the extra rivets
Kenneth T. Clark
Reviewed in the United States on July 14, 2022
Just installed it last night .Works well goes up and down pretty fast my old one was wasted it made a loud noise one night sounded like a gun shot went off in my door I rolled it down and never came back up.Anyway the hardest thing was drilling the pop rivets out take your time on the glass ones.Used the punch knock the center post down then 3/8 drill bit knock the remaining piece out with smaller punch.You will need 9 1/4 20 bolts 3/4 inch long and 2 1/4 20 1 inch long for glass. One by the motor tab sticking through door I turned the bolt around and put the nut on the front because not that much clearance.Also use nylock nuts they won’t vibrate loose. Takes about 1 and half hours to complete Did take the glass out and put it back in I figure it gave me more room to get the old one out.YouTube video by a1 auto was helpful.
Scott S.
Reviewed in the United States on August 21, 2020
Product is excellent. I read through several reviews and picked up a lot of tips & tricks - summary below...1) Ford uses rivets - not screws. using small hammer and punch - knock out center of rivets and drill out the rest (slowly) with a 3/8" in bit. if the rivet starts to spin, get small flat head screwdriver to dig into the aluminum to stop spinning2) be extremely patient when knocking out the rivets on the window glass...it took lots of small taps to get them out.3) lots of youtube videos on the mercury grand marquis / crown victoria - follow those4) several reviewer said to you nylon / nyloc nuts and bolts. yup i did same thing 1/4 - 20 and got several 1/2" and two 1" for the window. i put a washer as well.5) with regard to the window bolts - do not over tighten. get in snug and no extra after that - one poster mentioned he overtightened and broke the glass6) a little lubricant on the internal window guides is helpful while you've got the door apartgood luck!
Customer
Reviewed in Mexico on January 7, 2019
Quedó perfecto a un Grand Marquis 2004
Ryan Hanan
Reviewed in the United States on September 7, 2016
Part is direct replacement. Excellent Quality...revised design from OEM.Some important notes:1. Mine did not come with hardware. I used the Dorman 702-013 Regulator Hardware Kit (rivets)2. The complete assembly has the motor permanently attached and the 3 motor bolt holes will not line up with the holes in the door. In other words after you rivet in the motor mount you can not remove just the motor. The motor bolts will also no longer line up with access holes. Don't freak out.3. The instructions indicate 1/8" drill bit and 3/8" drill bit but I had to use 1/4" or larger to remove the rivets.4. Placing painters tape around the rivets when removing will help avoid scratching the paint.5. Removing the water proofing was a pain as it was attached with adhesive. New weatherstripping adhesive should be used to reattach it.6. My door had a metal bar riveted over the access hole which needed to be removed and reattached with rivets. This was not in the instructions.7. Overall the instructions were a good starting point but we're not very accurate.You will need a long reach rivet gun for one of the window rivet points. My door had a square hole about 1"x1" to insert the rivet gun through for that rivet point. It was very tight.It took about 1.5 hrs start to finish. This part is slightly different from the OE as the design is improved. The hardest part was removing the old rivets.Works great. Dorman has detailed instructions on its website.
Toydog
Reviewed in the United States on June 28, 2014
A common problem on these older Crown Vics. On my '93 the regulators are broke on all four windows. After seeing how easy it was to replace one on my Chevy, I ordered one for the Ford. A little more work here. You will have to punch out and drill out a bunch of rivets ( good video on youtube). I was worried about having to buy a rivet gun or finding hardware to install the new regulator, but the Dorman part CAME WITH a bag of nuts and bolts to complete the job. The regulator fits perfectly. The hardest part was getting the window to go back into the channels ( a little swearing here ). The window now goes up and down perfectly. One window down, three more to go. Thank you Dorman for a great product, and thank you Amazon for a great price.
Recommended Products
