Your cart is empty.
Your cart is empty.Install your Smart Thermostat Essential without worrying about wall imperfections. Specifically designed for Smart Thermostat Essential, the trim plate conveniently covers any scuffs, marks, gaps, and small holes left by your old thermostat.
Donnie
Reviewed in the United States on May 7, 2025
Size, curves, and color match the Essential thermostat design perfectly. Has a handy little built-in bubble level, and comes with four plastic wall anchors and screws.
Rosenberger
Reviewed in the United States on May 19, 2025
Expensive for what it is, but it fits perfectly to the devices listed in the description.
Phinphan
Reviewed in the United States on May 16, 2025
FYI this Ecobee wall plate WILL work if you have a 2x4 box in the wall, . There are 4 marks on the back side to drill for either horizontal or vertical mounting. Just remember to use the 2 white machine screws with nuts to attach the thermostat mount to the base plate.(you may need to shorten the 2 screws since they are a bit long and can interfere with the 2x4" electrical box in the wall). Once mounted, you can then mount the thermostat. You will be able to slightly see the white mounting screws from the side. No big deal. I rated this base plate a 4 out 5 because I feel the base plate is too wide and the fact that you can partially see the screws after mounting the thermostat. Would I buy again ? YES Its' the best option out there. I hope this review helps.
rbs
Reviewed in the United States on May 15, 2025
Made for Ecobee thermostat…works perfectly
Noel Rodriguez
Reviewed in the United States on May 13, 2025
Es tal y como se ve y funciona bien
Robert
Reviewed in the United States on May 11, 2025
All good.
Haggarts
Reviewed in Canada on April 30, 2025
I got this to replace my previous.It's or misstad, because the ecobee didn't cover the whole marks from it, and I didn't want to have to repaint the whole hallway.As you can see, it covered up the markings from the honeywell.Very nicely and screw marks and saved me from painting .I hope this was helpful
J. Layman
Reviewed in the United States on April 27, 2025
Fits well, looks fine. Not much too it. A bit too expensive for a simple piece of plastic but it is what it is. Hole from cover plate locks with hole from the base plate. Screw it to the wall with the baseplate, insert your wires, snap on your thermostat and you’re done. When snapping on your thermostat, make sure both sides are even and you push straight. Don’t try to snap in one side and then the other.
Ali B.
Reviewed in the United States on April 20, 2025
Ecobee’s own trim kit does not work for their own thermostats. See pictures.I had to get real creative with some self tapping screws in order to make my trim kit work. I had to drill through the plastic because as you can see the screw holes from the thermostat wire kit do not line up with the screw holes on the trim kit. This is the most basic of things and they managed to mess it up. Only the bottom one matches…But that isn’t even the worst part. Even if you don’t use the side screw hole (which again don’t line up) and just use the bottom one only, the thermostat doesn’t sit flush in the trim kit. It does not make a full connection and sits way too high and “tilted” off of the trim plate. Because the pins never get fully set, the thermostat will not turn receive power.So my solution to this, because I NEED a trim plate, was to lower the wiring piece just slightly and drill some self tapping screws into the left and right screw holes THROUGH the trim plate plastic. Now the wiring piece isn’t flush, and my thermostat isn’t flush in the trim kit. But it is connect and working now.The ecobee thermostats are great, don’t let this review knock them. They just need to fix their trim plate because it doesn’t work. What should have taken less than 5 minutes took me almost half an hour to figure out.
Recommended Products
