Your cart is empty.
Your cart is empty. Compatible with:
Fit 4.6L and 5.4L 2 Valve engines:
For 96-04 Mustang GTs 2V.
For 91-93 Lincoln Town Car 190 hp 2V.
For 92-97 Ford Crown Victoria/Mercury Grand Marquis 2V.
For 98-00 Ford Crown Victoria/Mercury Grand Marquis 2V.
For 01-02 Ford Crown Victoria/Mercury Grand 2V.
For 02-on Ford Crown Victoria Police Interceptor 2V.
For 02-on Ford Crown Victoria Police Interceptor 2V.
For 94-95 Ford Thunderbird 205 hp 2V.
For 96-97 Ford Thunderbird 2V.
For 94-95 Mercury Cougar 2V.
For 96-97 Mercury Cougar 2V.
For 97-02 Ford F-Series 2V.
For 98-00 Lincoln Town 2V.
For 01-02 Lincoln Town 2V.
Vehicle compatibility charts are for REFERENCE ONLY. Check your vehicle with OEM below to match your needs.
Gabriel
Reviewed in the United States on April 2, 2025
Worked as described, made it super easy to remove and install my valve seals and springs
Bob Builder
Reviewed in the United States on September 24, 2024
worked perfectly for removing and replacing valve springs, retainers, and seals. good tool
Zachary
Reviewed in the United States on August 29, 2024
The tool saved a lot of time from having to take the tool off and go to each individual valve, this tool allows 4 valves to be done without even taking the bracket off, it’s amazing
Jason
Reviewed in the United States on November 2, 2024
I used this to upgrade the springs on my 2002 mustang GT before a cam swap. The tool worked perfectly. Be sure to cover the oil return holes in the heads in the event a keeper falls off of your magnet.
Eng
Reviewed in Saudi Arabia on September 1, 2023
تم استخدماها لاستبدال سبنرقات محرك فورد 4.6 وممتازه جدا
Arturo
Reviewed in the United States on August 7, 2023
The tool worked perfectly for my 2002 Ford Mustang GT 4.6L 2V engine. I had it at top dead center, where I was then able to compress it down far enough and easily place the keepers back in with my finger. Used a tiny bit of grease and done. Tool worked as it should and it got the job done.
Damon
Reviewed in the United States on December 11, 2023
The cup will go over the valve spring on a 4.6 2 valve W engine. But with a washer it works perfect. Highly recommend this!
Joseph Mart
Reviewed in the United States on January 18, 2022
At first I tried to use a singular overhead style valve spring compressor, which failed miserably. I then was searched and found this tool which works wonderfully it's all high quality aluminum and the design of it allows you to do four valve springs with the tool bolted in the same location which saves a lot of time from having to move the tool for each individual spring like some styles. Very satisfied with this high quality product.
James Tillman
Reviewed in the United States on November 11, 2020
Ordered this when I was "mass buying" parts to get ready to rebuild the heads on my 2002 Mustang 4.6L 2v. Once it arrived, I didn't even open the box and set it aside for when I got the heads off. I didn't even question the possibility that it was the wrong part.I get the heads off and get them off my bench and it's time for this part to shine. I open the box, and not only does the part number on the part not match the box, it says it's for a 5.0 Coyote 4v.I tried this part every which way possible to get it to fit and work but no such luck. Really disappointed in the quality control of this company to let the wrong part get this far and into the hands of the customer. I'm now completely at a dead standstill until I can actually get a correct part
Recommended Products
