Your cart is empty.
Your cart is empty. Fits Modes:
YAMAHA BWS / ZUMA 50 (Horizontal engine),
BWS 100, Vino 50 (2-Stroke),
JOG /-Z /-ZR /-EX /-Poche /-Sport /-APRIO,
JOG /-ZII /-ZR /-C /-PRO /-BJ, AXIS / REX,
Grand AXIS, AEROX, NEOs 50 / 100.
MBK Booster, MachG, Nitro, Ovetto 50 / 100.
CHINA Cloned Minarelli 50~100cc 2T 1E40QMA / B.
Note:
NOT fits BWS / ZUMA 50 CW50, JOG / Riva Vertical models.
Gracias por el producto !
Reviewed in the United States on March 17, 2025
Muchas Gracias funciona perfectamente
Radiatedmocha27.
Reviewed in the United States on February 1, 2025
I'm sure if I had the right minarelli cylinder this would be a great addition and it is really good quality in terms of build and materials, only real downfall in design is the read valve material is thin plastic and I would recommend you swap it out for stainless steel or carbon fiber but for a street driven daily this will get you going down the road solid as the reeds are very soft and will deliver more fuel in the lower RPM range as they won't require as much air velocity to open
Jason Grimm
Reviewed in the United States on October 20, 2023
Pretty good quality intake, be sure to clean up the burrs before you install it though! There will be some small leftover casting bits inside which can flake off and damage your engine, but are very easy to remove with a file or Dremel. I think some people that say it does not fit don't realize it comes with a very large reed block, in my case I couldn't use the one it comes with but it bolted straight up with the smaller original reed block that fits my engine
Kaiden
Reviewed in the United States on May 4, 2022
So I got this hoping to put in on my 90cc clone Polaris engine and it fit perfectly and I had put a 24mm nibbi carburetor that fit perfectly in it as I probably could have fit their 26mm carburetor in it as the engine it being transformed as a racing engine.
Albert Einstein
Reviewed in the United States on March 16, 2022
DONT BUY!!! DIDN'T FIT MY YAMAHA JOG 50CC.The description is wrong
Rodolfo Velazquez
Reviewed in the United States on September 16, 2020
I love it I haven't tried it yet waiting for the rest but all in all it looks like pretty good product can wait to try it on my zuma thanks Amazon
Seania
Reviewed in the United States on June 6, 2019
Here's the info you need.Sizing/specs:The gromet is ideally for a 1" pipe,and it uses a 1" pipe.When mounted, either can face backwards towards the mufflers side, or forward towards the "driver side".Has the largest standard opening for the reed valves, with no rubber guide/limiter at the header to the reeds.The reed valves seem to be plastic, with a additional half-width metal clip to reinforce them. (personally, better then a all metal reed, but worse then a carbon reed)*Two vacum ports*Comes with:Two bolts/nuts to hold it together.Two hose clamps and a rubber 1" gasket/adapter.A single cork seal.The Bad:You can see in my pictures, there were fragile over mould metal edges, which flaked off with the slightest touch. There was already a loose flake in it infact. Which, would've broken the reeds/bearings first startup had I not caught it and used a dremel to clean up the nasty edges.The metal on the screw plates, and a few of the screws were also rusting.The screws could not take much torque from a flat head before starting shear, which is a issues as reeds need to be on TIGHT to prevent them from falling in.The Good:Largest unrestricted reed opening you can get.Reed screws use lock washers.Reeds are reinforced with aditional metal clips to maintain a seal.Reeds are not metal, but some type of clear composite or plastic.Would I recommend it?Yes, for the price it's very nice. Just sand down any mould overflow, or else you'll have a bad time.Pics:Of the poor moulding, rust, and a few other various parts.
Daniel Finley
Reviewed in the United States on July 29, 2017
Great item, reeds look great fast shipping perfect fit.
Recommended Products
