Your cart is empty.
Your cart is empty.Product Description
FB-4 Flat Steel Metal Brake Bender, 4-Inch Hand Operated Steel Bending Brake, 2.5 Tons Press Bending And Create Up To 90 Degree, High Flexibility
- Bending angle up to 90 degrees
- Bending mild steel plate up to 4.5 mm thick
- Easily mounts on any tabletop
- A gauge on the guide to show the ram position
High Bending Capacity
- This 4-inch hand-operated steel bending brake has a 2.5-ton pressing capacity and a pressing travel distance of up to 2-1/2". This sheet metal bender can bend to 90 degrees by simply turning the handle level until the desired angle is accomplished.
- The sheet metal brake bender can be used to press bend ornamental iron, mild steel, aluminum, and other metals.
Flexibility and Versatility
- Solid steel welded frame prolongs the durability of this metal bending brake.
- The base with pre-drilled holes can be easily mounted on any bench, thus ensuring stable and straightforward operation.
- For cold forming of steel and metals, this bender brake includes a setup plate for table clamping.
- The high-flexible 90-degree bending angle can be adjusted by simply turning a hand level. The scale on the guide shows the ram's position.
Wide Applications
- The sheet metal plate shear is a versatile tool used in various industries and settings, including metalworking workshops, home workshops, construction sites, automotive repair shops, educational settings, and hobbyist workshops.
Specifications
Scale
The scale on the guide shows the position of the ram.
Handle
This sheet metal bender can bend to 90 degrees by turning the handle level until the desired angle is accomplished.
Pre-drilled Holes
With pre-drilled holes, it can be easily mounted on any benchtop.
SK
Reviewed in the United States on September 29, 2024
Used for 3/8 aluminum rod worked well
Harry
Reviewed in the United States on July 24, 2024
All good
Frank T
Reviewed in the United States on June 14, 2024
This tool works and its well made.
Mr. Andy
Reviewed in Canada on June 14, 2024
I have used it to bend 1.5" x 1/8" aluminum flat bar. easy and clean. i'm sure it will come in handy again in the future. great tool to have when you need it. heavy and strong.
Tdlanders
Reviewed in the United States on April 8, 2024
The bends are not square or even. Putting marks and setting the gauge. It's okay for rough fabrication but not finish work.
Paul Yee
Reviewed in the United States on October 19, 2023
Use this tool to make motor mounts and brackets for my car project. Bent 3/8 inch steel and quarter inch aluminum without problems. Tool seems durable and will probably last a long time.
Toolmaker
Reviewed in the United States on December 1, 2022
It didn’t work very well then I noticed that the top strap was in a bind and wouldn’t work properly. Then I compared it to the picture on the box. That top strap is on upside down. Remove the pin, install the top strap properly and it works great.
Claude Salisbury
Reviewed in the United States on September 7, 2021
Difficult to use, especially when tying to bend on a straight line. Bends are coming out crooked since the alignment line gets hidden when the metal is installed.
Tuer
Reviewed in Canada on October 4, 2021
Good product and build quality. Only bent 1/8” x 2” wide mild steel; which it did this with ease. Mounted mine on a wooden hold down board and used spacers under each end of the metal to keep bend perpendicular.
A
Reviewed in Canada on March 11, 2020
Can’t go wrong with the price! So if people complain don’t listen. The unit works well and like every tool you need to learn it, it has a lot of moving parts but once you figure it out it’s fast. The bends have a much bigger radius than a sharp shop press brake but the tool it’s also 100 bucks not thousands for a proper press. I was bending some 1/8 steel brackets and I deducted 1/4” from each side or 1/2” overall and I got the exact inside measurement I was looking for. See attach pictures, I also show a bracket with a corner bent by a proper press brake and a corner bent by the kaka steel bender. You can compare. This is a great tools for small on the fly parts.
Greg H.
Reviewed in Canada on March 1, 2019
It's not a bad machine but the male die has a very round Edge so you're not going to get a sharp bend on anything. The edge is about a 3/8 radius, not a point and the female side of the die is quite rounded also. Unless you're trying for large radius bend, I wouldn't use this on anything less than 1/4 inch thick.
Mattiearthur
Reviewed in the United States on October 11, 2019
Works great on small jobs. I have been trying to use it without it being bolted to a bench. It really needs to be bolted down to make it easy to use. Nice tight bends.
Dale
Reviewed in Canada on September 29, 2018
I bought this tool to form a number of brackets for a go kart project. It works like a charm on everything I've thrown at it up to and including 1/4 inch by 1 inch steel bars. While there is some slight marking of the bent steel's surfaces, it's a lot less than I've seen on commercially produced parts. This is one of those tools that you'll wonder how you got along without it before using one. Highly recommended.
Recommended Products
$11.79
$ 5 .99 $5.99