Your cart is empty.
Your cart is empty.Product Description
Once mounted, the projector adapter will allow 20° of tilt and 360° of swivel so you can aim your projector at your screen.
The Kanto P101 is designed to fit most projectors and is commonly used in boardrooms and offices but is also ideal for home theatre applications.
Without the extension tubes, the P101 sits 3” from your ceiling. With the extension tubes, you can extend the length from 9” to 12”.
The P101 is shipped with four mounting arms attached to the tilt head, and four longer mounting arms are included in the box.
Customer
Reviewed in the United States on September 26, 2024
Simple, well made, easy to install bracket and, as you can see, worked perfectly for a tight space.
Anthony Serino
Reviewed in the United States on March 18, 2024
The good- I have no fear that my projector is coming off the ceiling with this mount, it's solid. It's inexpensive but still does the job.The bad - the system to attach the mount to the projector is a bit convoluted. It gives you little mounting arms of different lengths, since projectors have different mounting hole patterns. There was no hardware provided to mount the bracket to the ceiling (though there was more than enough hardware to mount the bracket to the projector). There's a bit of slop once mounted, but this is not a big problem in the end.One important note. Many people are complaining that the mount does not hold the projector in place, and that it allows their projector to move over time. This can be prevented if you use common sense. The people complaining about this missed two points in the instructions: 1. you can tighten the swivel point before final assemble. 2. Mount the bracket directly above the center of gravity of the projector. To do this, hold the projector in your hand in the spot the balances it. Now mark that spot and use the various length arms they provide to ensure your bracket column is above that spot. I actually had to cut two of them with a hacksaw to do this with my projector, but if you don't, it will drift over time.
John E.
Reviewed in the United States on September 21, 2023
Este soporte resulto ser un robo para mi que lo compre con la esperanza de acomodar mi proyector en mi sala de cine en casa el soporte es robusto tiene un buen acabado y opciones de configuracion pero se tambalea con el peso del proyector jamas pudi ubicarlo bien no se puede subir o bajar sin que quede descuadrado la imagen, el pibote que sostiene el proyector es una basura plastica super dificil de desconectar de la base lo pude hace entre dos personas con el riesgo que un proyector de 3000 dolares se caiga y se dañe jamas volveria a comprar esta basura estoy muy molesto con esta empresa siento que me robaron mi dinero ahi lo tengo botado en mi sotano no me sirve para nada exijo una devolucion o envio de otro soporte que en verdad me sirva
PAYET Christophe
Reviewed in France on July 11, 2022
Parmi les choix sur Amazon celui-ci m'a semblé le plus robuste. Il est effectivement solide, en revanche je confirme les autres commentaires qui disent qu'il est difficile à ajuster. En effet, j'ai du démonter au moins 3 fois, et faire des ajustements en prenant des marques avec un crayon. Pas fou. En revanche une fois que c'est réglé... C'est top.
T. E. Kainz
Reviewed in the United States on December 27, 2020
Because we live in an older manufactured home with 7-foot ceilings, I needed a low-profile projector mount. This unit took only about 20 minutes to install once I rounded up the drill, drill bits, screwdriver, and plyers. Once I determined approximately where the projector needed to be mounted, I adjusted a little to locate the nearest ceiling joists. A couple minutes with the drill driver and a pair of 3-inch lag bolts securely fastened the mounting base to the ceiling. Another 10 minutes to secure the mount to the projector and that was it. Easy to follow instructions combined with having all the parts in separate pouches made mounting the projector a relative breeze. From the ceiling to the lowest part of the projector is only 8 inches.
tintin
Reviewed in the United Kingdom on December 20, 2019
Very well made and totally solid when installed. Flexible options including multiple fasteners. You firstly mount a plate on the ceiling with or without one or both of the supplied dropper tubes. You then mount a bracket directly to the projector (plenty of adjustments and fastener options). The bracket on the projector has a spigot protruding from it with a couple of spring loaded clips. Once mounted, holding the projector, you push the spigot into the ceiling mount until the clips latch into place (just like door latches). The spigot is attached to the projector bracket by a tensioned ball joint (adjustable) and once mounted, you position the projector by putting pressure against the ball joint in the direction required. To remove the projector is easy, you simply push it up a little to depress the latches, turn the whole projector through approx 45 degrees and withdraw gently downwards. The latches are kept depressed and don't engage, allowing removal. All in all, it's an excellent design.My only criticism is that when adjusting the position of the projector, there is quite a bit of free play before you begin to put pressure on the ball joint. This resulted in a few attempts to get the perfect position. It's not that big a deal really, as once set you'll rarely need to touch it again.
Graham C
Reviewed in the United Kingdom on October 4, 2019
I don't often write reviews but this is one of those occasions when I felt compelled to do so. My requirements were for a ceiling mount with minimal drop in order to get the image as close to the ceiling as possible (I am projecting over a fireplace). It had to be unobtrusive (as it is in the lounge), easy to assemble and mount to a single ceiling joist. This mount satisfied every requirement. It is very compact and elegantly styled (as far as a ceiling mount can be). I attached the ceiling plate through the plaster board and joist using 2 x M8 Coach Screws and am satisfied that this is a solid installation (it needs to be as I sit underneath it!).To cap the whole experience, on opening the box and checking the comprehensive range of fittings, I noticed that 1 (out of very many) of the plastic spacer washers was missing (it should have had 4 of each size but only 3 of one particular size were in the pack). It made no difference to my installation because, like many projectors, mine only uses three support arms. Nevertheless, you never know what the future may bring so I emailed the company in Canada and the very same day they posted a complete set of 4 washers to me.In summary, I had looked at many different options before settling on this projector mount but couldn't find anything at this price point with such a compact, stylish and unobtrusive design - all of this supported by excellent customer service. Highly recommended.
Jorge Hernandez
Reviewed in the United States on September 22, 2018
Love it. Easy to install. Only 3 inches of height, and it’s a good price.... the quality is good enough compared for what you paid for. As long as you don’t mess with it once installed you are good.
The Engineer
Reviewed in the United States on July 5, 2018
This is a much better projector mount than my previous one made by Vivo () for my basement with a hanging ceiling. The Vivo mount was very difficult to work with due to the limited clearance left when mounted 2.5" above the hanging ceiling.The chief benefit is that the projector can be attached or detached easily. The second benefit is the adjustable clearance from 3 to 9 -12 inches. Note there is a gap between 3 and 9 inches. It can support either 3" or 9 to 12", not between 3 to 9". For that reason, it only gets 4.5 stars. Luckily, I was able to live with that limit although I would like to be able to have 7 or 8 inches of clearance.
Ed Wong
Reviewed in Canada on February 14, 2018
fast shipping. well design and easy to install.Accessories come with package is good enough for all different situation.
Dread Worf
Reviewed in the United States on December 25, 2018
The projector side of this mount is flexible and solidly designed. Ten extensible metal extension brackets are provided, of which you should be able to find four that will fit the bottom screw holes of virtually any modern projector. Once all screws are tightened down, this bracket assembly fits flush and secure to the bottom of the projector. In the center is a rotating tiltable suspension post that can be tensioned to allow either hand alignment of the projector angle or rigidly tightened down. So far, so good.The weak point of this mount is how the ceiling mounting plate and hollow extension poles attach to the center suspension post. The plate and poles slide loosely over the post and engage a pair of bent metal latches on opposite sides of the post. These latches pop into rectangular slots on the bottom of the plate and poles, providing safely lock to prevent the projector from falling off the ceiling plate or poles. A pair of tapped screw sockets are also provided for tightening down the plate or pole to the suspension post. The design flaw is that even when these screws are fully tightened, the projector can still be rocked back and forth within the loosely fitted rectangular latch slots.The best way I found to fix this problem is to use an exterior rectangular speaker mounting bracket instead of the supplied ceiling plate. This works because the diameter of the ceiling plate tube is the same as standard 1 3/8-inch loudspeaker mounting poles. Here is a link to a substitute speaker mounting bracket that will fit snugly and securely to this projector bracket's suspension post. The bracket's tensioning knob should be oriented against the suspension post's screw hole, not against the bent metal latch.https://www.amazon.com/EB9760-Exterior-Speaker-Mounting-Bracket/dp/B0007SL856/ref=sr_1_3?ie=UTF8&qid=1545706097&sr=8-3&keywords=speaker+stand+mount
bnext
Reviewed in Spain on January 11, 2018
Se adapta perfectamente al proyector (en mi caso un InFocus) y se mantiene muy estable, queda bien estéticamente. El adaptador más corto lo deja bastante pegado al techo que es lo que quería.
Recommended Products