Your cart is empty.
Your cart is empty.Product Description
1200° Spark Plug Wire Boots Heat Shield Protector Sleeve
Details
- Color: Red
- Length: 6"(15.5cm) Id: 1"(22mm)
- Packing list: Spark Plug Wire Boot Heat Shield Insulator Set Of 8
- Easy Installation: Just Slip On ( Sewn End Over Spark Plug ) for Maximum Protection
- Construction: Made from Double Wall Braided Fiberglass Sleeving ( Triple Wall At Sewn End )
- Description :
- 1. Spark Plug Wire Sleeves Can Rest Directly On Hot Headers And Other Engine Components Without Burning, Melting Or Becoming Brittle
- 2. Boots Will Work With 90 Degree, 45 Degree, And Straight Spark Plug Boots
- 3. Sleeves Resist Gasoline & All Engine Chemicals
- 4. Sleeves Can Withstand Heat Up To 1200 Degrees
Description
- 1. Spark Plug Wire Sleeves Can Rest Directly On Hot Headers
- 2. Boots Will Work With 90 Degree, 45 Degree, And Straight Spark Plug Boots
- 3. Sleeves Resist Gasoline & All Engine Chemicals
- 4. Sleeves Can Withstand Heat Up To 1200 Degrees
- 5. Sleeves Are Halogen Free & Non Conductive
- Replacement for Most Hot Rods And Classics Engines Including Gm
- Replacement for 265 / 260 / 289 / 273 / 283 Engines
- Replacement for 305 / 307 / 327 / 350 / 383 / 396 / 302 / 351w / 347 / 352 / 360 / 390 / 351c / 351m / 318 / 340 / 361 / 330 / 326 Engines
- Replacement for 400 / 402 / 427 / 454 / 472 / 406 / 428 / 429 / 460 / 400m / 413 / 426w / 440 / 455 / 502 Engines
- Replacement for All Spark Plug Boots and Wires Up To 1200°Degrees Fahrenheit (648.89°C)
TJ
Reviewed in the United States on August 12, 2023
Nothing wrong with these things but details are left out. There's a metal ring inside with a 18mm ID so only a straight plug boot or making your own boot terminations will fit thru it. If you handle the shield too much then the color starts to rub off.... In my case I removed the white threaded sewing on the one end so as I could wiggle the metal ring out and then a 90 degree boot could be passed thru. Then I folded the end within itself instead of worrying about sewing the end back up as it stays put.
Dougie
Reviewed in the United States on May 23, 2023
The Red Sox match the wires, call him cool socks, cause they keep the wires cool next to the headers on my 66C 10 Chevy 350 And they look cool
Arik Y.
Reviewed in the United States on September 5, 2022
yes, the color is a bit stained on the hands during the install, but its not fading through time (at least not quickly)i believe it provide some isolation from engine and exhaust heat
P. Dean
Reviewed in the United States on August 28, 2021
Just got around to trying to install these and they are garbage. I was able to get one on the wire and boot but it did not look right, so I tried to remove it and it frayed and pretty much was impossible to get on again. They fray and are difficult to fit over LS1 plug boots. I would love to return them but the window on returns closed.
paul garcia
Reviewed in the United States on December 10, 2020
I got these for my 2003 tahoe 5.3 at a fraction of the cost of some other brands out there they they have been on there for a while now they seem to be holding up fine
dannie r.
Reviewed in the United States on October 22, 2020
I installed the heat shields on my bbc 427 the headers I have are close to the spark plugs. I had melted a couple of the plug wires Pryor to installing. They look good on my engine and although I haven’t run it very much yet I feel it’s exactly what I needed
OregonKatt_Trainer
Reviewed in the United States on July 17, 2019
I used a second set of 1800 degree closer to the header pipes because my motor runs hotter on the exhaust than a cast iron stock header.These solve a problem I never knew about because the engine is covered up on a motor home and all I knew was it was misfiring sometimes. Spark plug wires were burned all the way through on 3 cylinders.
Pops_Silva_Fox
Reviewed in the United States on December 10, 2018
Had to return. Did not fit over my spark plug wires.
Recommended Products
$64.20
$ 29 .99 $29.99