Your cart is empty.
Your cart is empty. Handwired with superior components and craftsmanship, ObsidianWire kits are designed to give you greater clarity and control. The solderless connectors in every ObsidianWire Wiring Harness can be used again and again, allowing you to perform quick and easy pickup changes faster and easier than ever before. It is the perfect tool if you like to experiment with your tone.
This harness is for vintage Tele purists using the tried and true formula of professional grade components and craftsmanship to present the sounds of a vintage Tele. This kit has a master volume, master tone and three way switch.
Also included is a Volume Mod / Treble Bleed upgrade, which preserves high end frequencies and improves taper when rolling back the volume.
ObsidianWire uses only the best components in their kits. This ObsidianWire wiring harness comes with:
2 x Hand Matched Emerson Pro CTS Solid Shaft Pots 250 k w/.250" (Audio taper) (+/-6%)
1 x Genuine Oak Grigsby 3-Way Switch
1 x Genuine Switchcraft J11 Mono Output jack
1 x NOS Russian Cold War Era 0.047uf K42Y-2 PIO Capacitor
1 x Premium Volume Mod / Treble Bleed Kit
1 x Pre Printed Wiring Diagram Included
IMPORTANT NOTE: This ObsidianWire kit is designed specifically for American and Mexican series Fender Telecasters. Fit on any other instrument is not guaranteed.
okenter
Reviewed in the United States on February 26, 2025
This wiring kit made it so easy to install new pick ups in my telecaster. The installation was very simple, and the guitar sounds awesome. The only issue I had is that the 1/4” output jack wanted to turn when I was trying to tighten the nut that holds it in place. I think there should’ve been a locking washer between the output jack and the guitar to keep it from turning while tightening the nut.
Cody Sellers
Reviewed in the United States on March 31, 2024
What an incredible product. No soldering. No mess. No extra work. Easily screws onto pick guard and wiring pickup is so easy even for the inexperienced. It comes with easy to follow directions for wiring. As someone building my first guitar there was no other option.
BDW
Reviewed in Canada on November 24, 2024
Picked this up for a partscaster build and it works great, it's super easy to install and required only a few mins. Would highly recommend.
Rick
Reviewed in Canada on October 27, 2024
It looks good and it works good but man, the little tabs that you have to force these wires into are horrible and it makes the whole swapping process tedious and annoying. Next time, I’ll just solder… way faster and easier.
Craig Terrones
Reviewed in the United States on October 16, 2024
I switched out the stock harness with this new one from Obsidian. I installed it along with some Fender G4 noiseless pickups. The guitar is now as silent as can be. The grounding circuit is solid. Treble bleed works great. The only issue that I had — my lead wires on the neck pickup were too short to reach the input jacks that are between the two pots. I had to flip the control plate so that the pickup switch is on the bottom. Not a big deal for me but the tone knob is now on top and the volume below it.
wetippett
Reviewed in the United States on June 5, 2023
This is truly an exceptional upgrade to factory wiring
Michael D Opel
Reviewed in the United States on September 26, 2022
These harness are way too expensive for what they are. GFS kwikplug is a far better, far cheaper option.
Stephen Matthews
Reviewed in the United States on September 17, 2022
Maby I missed something, but I was under the impression that you got knobs and the control plate with the order.I didn't.I just got the controls . Anyway after I got them installed.It's working fine.
Fred B.
Reviewed in the United States on August 2, 2022
Very well made perfect fit.
Recommended Products
$13.24
$ 6 .99 $6.99