Your cart is empty.
Your cart is empty.Shock mount that can be used by chewing the microphone mount on your camcorder. It can be attached to microphone mounting mount with 0.9 - 1.1 inches (24 - 27 mm)
カスタマー
Reviewed in Japan on May 14, 2025
ズーム音やオートフォーカス音、冷却ファン音などが気になっていましたが、劇的に解消しました。振動を拾わないのと、マイク位置がカメラから離れるためと思われます。パナソニック（CX350）のマイクホルダーはソニーなどに比べて小さい（推奨マイク径21mm）ので、装着できるかどうか一か八かで購入しましたが、無事に装着できました。パイプ部はネジ止めで外せるので、万が一合わない場合は、径の合った木の棒などにショックマウントを取り付けることもできそうです。
J Starr
Reviewed in the United States on April 7, 2021
This works well.... I got tired of hearing bumps in my audio every time I moved something on the camera, or pan the camera by touching the handle or hang my headphone on the tripod handle...this took care of it.
HF
Reviewed in Japan on July 1, 2019
小型カメラ例えばNX5辺りのカメラにガンマイクを直に挿すときのハンドリングノイズの低減にかなり有効です。編集した人からはなんでこんなにハンドリングノイズが少ないのか不思議がられた事があります。
mig
Reviewed in Japan on October 25, 2018
Vカメのガンマイクホルダーでは完全に動作音、グリップノイズは取り切れるものではないのですが、なるべくコンパクトなクッションマウントはないかと探していたので重宝しています。
Martin S.
Reviewed in the United States on July 31, 2017
Works as expected.
Johnentwistlespout
Reviewed in the United Kingdom on January 25, 2017
Great holder that perfectly first camcorders with a tubular non/suspension mic grip (for instance the Panasonic DVX200). The mount is quite large and lifts the mic up about an inch above the generic holder - which helps keep a windshield out of frame. Two additional rubber suspension bands are also included. The mount itself is constructed from fairly rough plastic a steel tube. Fairly expensive for what it is but it's fairly niche so to be expected.Recommended.
Cameraman Bill
Reviewed in the United States on February 4, 2014
I bought this to free my hot shoe for an on camera light, using the camera's mic holder with this to still achieve the same shock mounted mic affect. The Shock mount is a little heavy to be used in conjunction with my camera's microphone holder, causing the whole system to be right heavy and wobbly. Decided to put the on camera light off to the side with a hotshoe extender instead. Overall does what it's supposed to just not with my setup.
bknewhaven
Reviewed in the United Kingdom on October 19, 2012
The NTSM5 works well with my NTG1 mic, but I still found I needed a bit of foam padding to secure it in the microphone holder on my Canon XH A1 camera. The thicker end is too big and the round smaller end slightly too small. But a small bit of foam solved the problem. Does a really good job of removing all handling sounds on the camera from the mic.
D. Sanders
Reviewed in the United States on June 1, 2011
I bought the Rode SM-5 mount to use on my Canon XHA1s camcorder with a NTG-1 Rode mic. With a Dead Cat windshield, the hairs were visible in the frame (wide shots) because the on-camera mic mount isn't tall enough. So the SM-5 solved that issue for me.
Recommended Products
