Your cart is empty.
Your cart is empty.Product Description
These are our 3rd Generation error free led turn signal light bulbs, come with all-in-one connection with better wiring decoder to prevent overheat, much safer compared to tradition load resistors.
Advantage:
Non-polarity design,compatible for both ck/srck and standard socket.
More than 400% brighter than original halogen bulb, full aluminum housing for better heat distribution.
Built in constant current ic for longer life span & low power consumption.
Luis Gutierrez
Reviewed in the United States on March 20, 2024
Installed o my 23' Explorer ST and I can say that it changes the overall look from those nasty old school bulbs. Upon quick installation I did notice the receiver gets a little too hot wich is understandable. But to make it permanent I added the lubricant to prevent corrosion on the original bulb harness and then imputed the new LED wiring into it, after plugging it in I recommend to wrap it with electrical tape to prevent anything whether is debris/water/moisture entering the connection. Further more the original silicone washer/water seal I installed over the LED bulb to make not only a tight fit but for added protection against moisture and or water entering the actual tailight itself. Finally the receiver I double sided 3M tapped it to the body of the car (to metal) so that way is not bouncing around and possibly prevent any plastics or wires melting from the receiver getting hot. Overall looks great and for longevity is something I have yet to experience since I just got them installed today. Overall great product so far and highly recommend
Conor
Reviewed in the United States on November 22, 2024
Bought these a while ago but only installed 6 months ago. 1 just burned out. Don't know why but super disappointed they didn't make it very long, especially being so much more expensive than the old kind that last years. Don't buy these.
Michael R. Rosario
Reviewed in the United States on August 5, 2023
The resistor does get very warm if the lights are left on for a prolonged period of time (i.e., using the hazard lights). I would not recommend these if you use these as daytime running parking lights, they will get very hot. Only use these as turn signal lights only, as you will only use these, at most, for about an average of 1.5 minutes, and as less as 30 or so seconds. Also, rig them so that they are not touching any non heat-resistant plastic pieces or thin wires. They are bright and useful, but would not recommend them for constant use. Will be waiting to see if the manufacturer will produce similar lights with a perfected resistor that is not prone to overheating. It’s also best to acquire products that are certified as well ✅
F
Reviewed in Saudi Arabia on July 22, 2023
Looks good and bright comparing to OEM bulb
Steve
Reviewed in Canada on June 21, 2023
I am currently using these in my 2022 ford explorer, they are nice and bright and add a little more “ Luxurious Look “ to the rear signal lights. No hyper flash at all, had them in for about a year now through summer and winter and still going strong.
Dillon Higgins
Reviewed in the United States on November 25, 2023
I’ve bought these for several vehicles and I’ve never had a problem with them. They don’t fit into the socket like the traditional bulb does they just squeeze in but I’ve never had a problem out of this. There’s no hyper flashing and they are very bright. Definitely and improvement over stock as these are brighter and more noticeable. Plus the instant on and off with the LED vs halogen is one of my favorite things.
PatM
Reviewed in Canada on December 20, 2022
These fit perfectly my Explorer ST 2022. Amazon fitment guide says non compatible but not true. No flash required and no fast blinking. Only thing left to find out now will be longevity. Great improvement at low price
Joel S. Desrochers
Reviewed in Canada on December 14, 2022
Bright light, easy to install, don't know about the longevity yet
KSF
Reviewed in the United States on May 13, 2021
Just installed, so I can't speak to the longevity. Product appears well made, stout materials. I had just purchased a used 08 Sebring from Volvo Fort Myers, steer way clear of that dealership, and they installed LED lamps for the turn signals with no resistor creating the hyper flash. I waited 1 month for delivery over a seat issue so by the time I finally got the car I had forgotten about the turn signal issue. The only difficult part of the installation was big hands, small area. I did tape the resistor lead into the socket with 3m Super 33 electrical tape to further secure and dust proof the connection. I also used a couple of cable ties to secure the leads so I wouldn't have knocking or rattling coming from the fenders. I'll update if needed, but right off I'd buy them again. Great cure for older vehicles.
Lucas Cuellar
Reviewed in the United States on October 29, 2021
This isn't my first time buying LEDs from this company... This is actually my third set of LEDs!The first set I bought was back in spring of 2019. They were very bright, flashed nicely, and didn't hyperflash. They are still installed in my old car and worked fine up until when I sold it. Which was September 2021.The second set I bought was in spring of 2020, I have them installed in the rear of my car and they still work perfectly. No hyper flash. The first two ones were red by the way, which are identical to the amber ones other than that they are red.The amber ones which I just recently bought, work the exact same as the previous red ones I own. I love them! Anyone that buys these will have no regrets. If I ever need more I will absolutely buy them from this company. Thanks
Ryan
Reviewed in Canada on August 8, 2020
Just received this item on 10 june and just today 8 Aug same year the hyperflash has quit. Just shy of 2 months and possibly only installed for 1.5months. Very disappointed on the hyperflash module. The mounting of the lightbulb itself is a great design as its all a rubber type material so you dont have to fight notches.
Bryan
Reviewed in the United States on April 28, 2020
This is a well-designed light for anyone requiring 3157 LEDs (meaning these lights are on constantly for parking lights and flash brightly as turn signals). Good construction and shipping was very fast (only 3 days amidst the covid-related delays). The rubber boot on the bulb pops into the bulb housing base with ease and creates a snug, secure, water-tight seal. The inline chips/resistors are nicely made and lightweight. It's not necessary to mount the resistor boxes, as their weight is minimal and will in no way pull these bulbs from the sockets if allowed to hang or rest freely - just be sure to secure them away from any moving parts. Lights are very bright (3-4x brighter than OEM filament bulbs) and do an excellent job of filling the lamp assembly with even light, even in bright sunlight. Makes your signals/running lights clean, crisp and highly visible. These lights are worth the extra $ - you get what you pay for and these remove the need to splice in external resistors. My vehicle required 4 of these bulbs for the front lights - well worth it!
The 2 Liter
Reviewed in the United States on July 22, 2019
2005 Dodge Ram 2500These worked great and were cheaper than other brands, have a better resistor heatsink setup and actually work PROPERLY with no hyperflash.I removed the bulb cap inside the housing because, well, why have projector lenses on these bulbs if you COVER THEM UP!?Very impressed with the build quality. I do hope these seal properly though as they don't have the same mechanism for attaching as the OEM bulbs do. Basically just using the pressure of the silicone piece to seal. I'll update as time passes if there are any issues.Pictures are for comparison. first two shots of my driver's side light are a normal, incandescent 3157NAK at full power and running light and the passenger side shots are of the LED bulbs, again at full power and running light. Took during the day to show that they are in fact SIGNIFICANTLY brighter.
Recommended Products