Tengo 4 PLC, dos de 200 Megabits y dos de 1 Giga. No se hablan entre ellos (es lo normal) , pero cada pareja funciona perfectamente cuando se instalan en el mismo circuito eléctrico. Si obligas a la señal a atravesar un tablero de control, sigue funcionando pero a unos 20 o 30 megabits (es normal) no importa si los PLC son de 200 o 1000 Megabits. Lo ideal es colocarlos siempre en un mismo circuito. Saludos.

Highly recommended

These things are amazing! And two of them for only $50 is an amazing price. I just moved in to a condo with a garage that is connected to the same building, but there are several concrete walls between my unit and the garage. I wanted to get WiFi to work in the garage, but no matter where I placed my router inside the house, I could not get WiFi signal in the garage.So, the solution was to add a WiFi access point (hot spot) in the garage, but there was no way to run an ethernet cable from the garage to the house, there was no coax cable in/near the garage to use MoCa, so powerline was my only choice.The really strange thing is how my garage is wired. It is not connected to the breaker panel inside my house. There is a separate breaker panel on the outside of the building, which is connected to one of my neighbors' electric meters (Strange, right? Hey, free electricity in the garage!), with a separate cable that runs underground to the big green box that contains the transformer. I estimate that there's at least 300' of electrical wiring between the two units, and plenty of interference due to being connected to two separate breaker panels and going through two electric meters. I also couldn't tell if the two were on the same phase, so I bought a phase coupler. More about that below.I was doubtful that this would even work, but... the connection light turns red, indicating "weak signal", and...When I use speedtest.net, I get pretty consistent speeds of 12Mbps from the garage. That's plenty for my application because I just wanted to connect a Ring camera above the garage door, and a nifty smart garage door gadget. I only need 2-3Mbps for this application, so I'm overjoyed with 12Mbps.In order to get the signal to cross phases, I installed this phase coupler (see the attached photo):https://www.amazon.com/gp/product/B00VV7HYDCIf you don't understand the two phase power that is present in most North/Central/South American homes, you should hire an electrician. This phase coupler is capable of 3-phase also. Apparently some European homes have 3-phase power. I've personally only seen 3-phase power in industrial applications.After getting the powerline adapters to work, I used an inexpensive Wireless Access Point (WAP). I only needed 2.4GHz, because both the camera and the door opener only use 2.4GHz. Here's the WAP I purchased:https://www.amazon.com/gp/product/B004UBU8IEAnd, in case you're curious... here's the garage door gadget:https://www.amazon.com/dp/B075H7Z5L8

Las frecuencias de 5 GHz se (las que usan los routers N-AC) se han vinculado en pruebas de laboratorio a cancer y daño en ADN. Si quieres tener excelente velocidad de transmisión en tu casa con la seguridad de no usar 5GHz con tantos transmisores (redes mesh), la mejor opción es esta. Además de que no es necesario hacer perforaciones para poner cables de red.

1 Year Update: It's been an year & these have not given me any trouble. Probably twice I had to just unplug and plug them again because they lost the sync. Apart from that, the speed has been optimal & they have allowed me to put my smart TV at places where I could have never imagined.--I bought these as an enhancement to my older 100M trendnets, which work great. I recently got 100 Mbps Internet and the trendnets were struggling to get me that speed.This does the job perfectly and I can easily get 50+ Mbps. I was not expecting any more. The product is big when you compare it to a power socket. The size can be improved in next model.For all the people taking 1G as literally 1Gbps, it does not work this way. Any networking product is rated in an ideal world enviornment and you always get 20-30% less in real world.

Looks nice product. Has not been fixed yes.. it will be fixed in 2 weeks time.

This is a review to address all of the reviewers who claim this powerline device does not perform, with reasons why they are incorrect & they are not looking at the right part of their issue.Background of my installation:All wiring is CAT 6High end router, running as base & 2nd wired AP. Primary router directly wired to Modem.Primary router connected to a 16 port rack mount gigabit switch.Switch connected to a CAT 6 patch panel for multiple wires, some wires direct into switch.One Powerline adaptor direct wired into switch.I wanted to bring wired ethernet out to a detached garage to reduce the wifi network load, so a powerline adaptor seems to be the ideal solution (it is).I have multiple dedicated circuits from the breaker panel to the garage, the powerline adaptor in the garage is connected to one of these that also runs various items out there, so it is a shared 20A rated circuit (12 GA wire).I added a dedicated outlet to this line as it enters the house, which is in front of the breaker panel, where the 2nd powerline adaptor is located. Total wire connections, with screw terminals in the outlets plus wire nuts = 2 nut + 2 screwed terminals (not backstab into the outlets, that is a terrible connection at the best of times)After installation, this gave me a rock solid 840Mbps signal.To test the losses in the system, I left the one inside the house where it is, close to the switch and connected the other one to another outlet in my office. This is fed by a totally different circuit on the other phase leg of the breaker panel & is a 15A circuit, with 14Ga wires. This means the powerline signal runs in one breaker, over the bus bars & back out another breaker to the outlet in the office. I am not sure how many wire connections it goes through but at a guess, (nuts & screwed terminals) it is at least 6.This yields a solid 427Mbps on the line I am connected to as I type this review.Every time a signal goes through a connection between wires there is a signal loss - like friction on a surface, so the signal loses efficiency each time. With a dedicated line & 4 connections, I lost under 20% of the maximum possible speed with good wire & good connections. With the signal going over the bus bar, changing wire size & multiple connections I lost 58% of the maximum possible speed.All the wiring in this house is under 3 years old, all the connections are rock solid - I know this as I wired it under the supervision of a VERY skilled electrician who teaches electricians & consults for local inspectors. All connections are screwed not back stab, as a screw connection will give a higher quality of contact and less likely to cause issues with just normal wiring later in life. The screw nuts are tightly wound onto the wires, which were wound together before the nuts were put on. If the wires are not wound together, you have high resistance and possible wiring issues later ( a friends father who is a retired electrician makes a fortune in his retirement simply re-making these lazy connections in new build houses that have wiring issues).So what I am explaining here is that, to expect 1000Mbps is not realistic outside of a theoretically perfect wiring situation, which is not going to happen in real life. However, if you have older wiring, oxidation on the joints (highly likely in older wires), multiple connections between wires & inside circuits, backstab wires into the outlets & not screwed, insufficiently tightened screws on the terminals, smaller gauge wire etc. etc. then you WILL get signal loss. Quite significant signal loss. I lost 58% in a well constructed system, but I still get a LAN speed inside my house that is faster than most people will ever got for an internet download speed anyway. Much faster.If someone has complaints about a poor transmission speed, you are looking at the wrong culprit by looking at the powerline adaptor & only blaming it. Based off my experiment, I highly suspect that 99% of the issues people are seeing are 100% in the wiring quality in the house itself. There are so many older houses & new ones with bad wiring in them this is where you need to look first. They are not hard issues to improve. Shut off all power to the circuit you want to work on (check that it is off) and then check, clean & tighten every connection you can find in that circuit. After you have done that all the way from one to the next adaptor, re-test your transmission speed, I think you will find it has improved. As long as it is faster than your internet download speed, then it is already faster than you need it to be and it is not the bottleneck in your signal transmission.I was doubtful as to what these things could do at first, but after experimenting & looking at the setup carefully, I am actually quite impressed. The line I will get out to my garage will be a phenomenal fast line & I am really pleased with that.I paid full price for the adaptors, They were on a 1 day sale that anyone could have got when I bought them, I didn't get offered any compensation, freebies or anything else for writing this up. I did it because I like to read reviews of products to see what I can learn from people who have actually used the product & not ones that have just looked at it in the box & said it is awesome. Actual product users & their experiences. I saw people who have had issues & people who have had success, so I wanted to try for myself & see how the product performs under different conditions to see why there was a range of results. I think I found out why.I hope this has helped some of you & helped you get internet to the darkest corners of your locations in a reasonable manner.If you have any doubts about attempting anything with the electrical system though, please don't touch it. Call an electrician, never risk your life with breaker boxes & electricity, it is not worth it.