Your cart is empty.
Your cart is empty.Features: double rows, 10Pin female to 10Pin female header with both end, compatible with 2.54mm spacing pin headers. Idc flat Ribbon cable, used for most Atmel AVR jtag debuggers, in-system programmers, isp download, etc.
Pilar Calleja
Reviewed in Spain on January 15, 2025
Ha llegado rapidísimo el pedido. Bien envalado.Eso sí, el cable es escaso, más bien 96cm.Me ha llegado justito para poder enganchar en el cuadro de mando de mi caldera. Pero era imprescindible instalarlo hoy por eso no lo he devuelto a tener en cuenta si necesitas el metro bien medido
Santa Clause
Reviewed in Germany on September 1, 2023
Lieferung war schnell da und die Kabel funktionieren der Erwartung gemäß gut.
Gérard D.
Reviewed in France on April 28, 2021
C'est un cable.
Customer
Reviewed in Canada on September 7, 2020
From other review it's stated it doesn't work with Creality Ender printer.That's just because pinout is different. To make it work you just need to flip over wires from one end.For seller it would be a hint to exptend the market.
Cody
Reviewed in the United States on May 16, 2020
Yes it is reversed on one end, but it still works fine. It's the cheapest route and I didn't have the terminals at the time nor did I want to buy ribbon cable. The red cable on one side will help show which orientation the connector needs to go if you do in fact need to cut off the tab to turn the connector around for your purposes. In my case I was extending my Ender 3 Pro's display screen. I used the supplied snip tools to just cut the tab off the screen side's connector instead of an exacto to prevent a slippage oops, and then plugged right in nice and snug just fine. Did not bother cleaning up left over tab as that helped keep extra grip.
Customer
Reviewed in the United States on January 8, 2020
Cable arrived fast, good quality cable and connectors, Thank goodness that I looked closely as I was hooking up the cable or I'd have blown out my equipment. With a keyed IDC cable it's critical that the connectors are on correctly since you can't reverse the connector in the sockets. In this case the cable was made incorrectly. I really needed the cable so I tried to remove an end and fix it but it's nearly impossible to remove one without breaking it (which I did) so I'm ordering connectors so I can fix the cable. Amazon the entire stock of cable should be checked if you hold up both connectors side by side with the key facing away from you the the RED wire should be on the same side of both of the connectors. If one is to the right and one to the left one was put on incorrectly and that cable could blow up equipment.Update, even though I broke the connector I was able to use my vise to re-crimp the wire in the connector and get things working. I'll just have to buy a new connector someplace, in the short term superglue to the rescue....
StoremanUK
Reviewed in the United Kingdom on January 4, 2020
Having ditched the cumbersome control box for the CR-10 I wanted to mount the stock display to the front of the printer frame but the stock ribbon was far too short. This cable reaches with some to spare. Worked perfectly and no need to reverse one plug to get the display to work.
ItsATrap
Reviewed in the United States on September 2, 2019
I bought 2 of the 10-pin 1 meter cables to extend the display on my Prusa MK3S. As several other reviewers have noted, this is not a straight through cable as shown in the photos or described on the page, the cable is in fact reversed on each end so they pins are flipped. You can still make the cable work if you trim off the alignment guide on one end and insert it upside down, it comes right off with some wire cutters. Other than the cable being reversed requiring modification it seems to work well to extend my 3D printer's display.
Larry Chambless
Reviewed in the United States on August 27, 2019
Just long enough to move the LCD around where you need it
JD
Reviewed in the United States on February 2, 2019
I picked this up to replace the cable on my Ender 3. I got everything hooked up and nothing worked on the LCD. I double checked my connections and tried again. Nothing. I inspected the cord and noticed that the triangle did not line up with the red wire. That would explain my issues.
P. H. Yokel
Reviewed in the United States on April 30, 2019
Good length, decent build quality. Used them to connect my Ender 3's LCD/SD card reader to the MKS Gen L board I put in it. It works well and didn't even have to spin the connector to the LCD. The cables did come with different #1 pin, the dark stripe on the outside of the cable, one was striped on the right the other the left of the key/tab on the connector. Would buy again.
J. Gibson
Reviewed in the United States on April 12, 2018
Works great to connect Turnigy 9xr Pro RC transmitter to a external RF module. The pin spacings are exactly the same size.
Vic AZ
Reviewed in the United States on October 11, 2017
Works great with RAMPS 1.4 and Graphic Smart Display Controller. Needed extension for my Cubex conversion - worked as it should.
Recommended Products
