- Home
-
All Categories
- Sports & Outdoors
- Automotive
- Industrial & Scientific
- Clothing, Shoes & Jewelry
- Musical Instruments
- Kitchen & Dining
- Pet Supplies
- Arts, Crafts & Sewing
- Sports Collectibles
- Baby
- Toys & Games
- Patio, Lawn & Garden
- Computers & Accessories
- Electronics
- Home & Kitchen
- Office Products
- Tools & Home Improvement
- Grocery & Gourmet Food
- Cell Phones & Accessories
- Camera & Photo Products
- Appliances
- Video Games
- Health & Household
- Beauty & Personal Care
- Payment
- About Us
- FAQ
- Privacy Notice
- Shipping & Returns
- Contact Us
Your cart is empty.
Your cart is empty.Product Description

How the Leak Detector Works
Step 1
Just install the valve in front of inlet tube and put it with detecting metal down on the floor near water systems.
Step 2
As detecting the leak, it will initiate an Audible alarm and indicator will light up.
Step 3
It will automatically cut the water supply when a leak is detected.
IDENTER Leaky Savior Auto Water Leak Protector Shut-Off Water Valve shuts off flow to the water system as a leak should occur. It can avoid water damage from a leak effectively!

Package includes:
- 1 x Auto water shut-off valve
- 1 x 9V Battery
- 2 x Quick fitting 1/4"OD-1/2"BSP
- 2 x Quick fitting 3/8"OD-1/2"BSP
- 1 x User Manual
Technical Specifications:
- Operating Voltage Range: 9 DC Volts (Alkaline battery only)
- Operating Current: typical 1 mA, maximum 15 mA.
- Cable Length (for solenoid valve cord): 1.5 M
- Connection: 1/2 inch BSP male
- Environment temperature: -20 ~ 80℃ / -4 ~ 176°F
- Maximum Pressure: 6 Bar

Powered by 9V alkaline batteries, the auto water shut-off valve can also shut down when reaching a low battery state.
As long as you install this valve in front of inlet tube and put it with detecting metal down on the floor near water systems, you will not worry about water leaks anymore!
Installation Steps:
Step 1 - Install the Correct Fitting: Choose the appropriate quick fitting based on your water line size: either the 1/4" OD to 1/2" BSP or the 3/8" OD to 1/2" BSP. Attach the fitting securely to the leak detector to ensure a proper seal.
Step 2 - Insert the Battery: Open the battery compartment and insert the 9V alkaline battery included in the package. Make sure the battery is properly installed to power the device.
Step 3 - Shut Off the Main Water Supply: Turn off the main water supply to your house to avoid any accidental leaks during the installation process.
Step 4 - Drain the Water from Your Faucets: Open all nearby faucets to allow any remaining water in the pipes to drain completely. This will make it easier to cut the water line without water spilling out.
Step 5 - Cut the Water Line: Carefully cut the water pipe where you plan to install the leak detector. Ensure the pipe is dry and free of water before proceeding.
Step 6 - Connect the Pipes to the Leak Detector: The elbow valve on the leak detector has an engraved arrow to guide the installation. Connect the pipes according to the arrow’s direction: the tip of the arrow indicates the water outlet, while the tail shows the inlet. Be sure to follow this orientation to ensure proper water flow and functionality.
Step 7 - Position the Leak Detection Plates: Place the metal leak detection plates on the floor near a potential leak source, such as near a water filter or under a sink. Make sure the plates are flat on the ground to accurately detect any water leakage.
Step 8 - Activate the Leak Detector: Press and hold the activation button for four seconds to power on the device. The leak detector will now be actively monitoring for any water leaks.
$135.30 $135.30
$ 53 .99 $53.99
$229.98 $229.98
$ 93 .99 $93.99
$39.39 $39.39
$ 17 .99 $17.99