Your cart is empty.
Your cart is empty.Product Description
-
- Can only be used with round button maker.
- Does not comes machine. Please purchase separately.
-
-
-
-
Button Maker Set
- Commercial-Grade;
- Interchangeable Mold;
- 1000 Sets of Plastic-Back Button Supplies.
-
Button Maker Set
- No Need to Assemble;
- Lightweight;
- 200 Sets of Plastic-Back Button Supplies.
-
Large Bulk Button Supplies
- Plastic Back;
- 500 Sets.
-
Square Button Maker
- Lightweight;
- No Need to Assemble;
- 200 Sets of Plastic-Back Button Supplies.
-
Pocket Mirror Supplies
- Mirror Back;
- 100 Sets.
-
Button Supplies
- Keychains Design;
- Bottle-Opener Back;
- 100 Sets.
-
Metal Button Supplies
- Slick Metal Back;
- 100 Sets.
-
Heart-Shaped Button Supplies
- Metal Back;
- 100 Sets.
-
Fixed-Pin Button Supplies
- Plastic Back;
- 200 Sets.
-
Metal Button Supplies
- Slick Metal Back;
- 200 Sets.
-
Plastic-Back Button Supplies
- Plastic Back;
- 1000 Sets.
-
Button Supplies
- Fridge Magnet Back;
- 100 Sets.
Crystal
Reviewed in the United States on January 21, 2025
I ordered these button supplies in a pinch when I ran out halfway through a commission, but they're as bad as I feared.The metal face and backings themselves are okay quality. The faces are comparable to the old set I had, but the backs were a weird texture and I didn't like how much wiggle room the needle piece of the pin had. They were also shaped kind of funny, so the pin part was very difficult to fasten under the hook once opened.The mylar sheets are what really brought this review down to two stars though. On top of being thinner than the higher quality ones I already had, they were sized incorrectly. It's hard to tell, but in my first two images, the first photo is of a correctly sized mylar sheet from my old set, whereas the second photo, based on the ripple of the glare, you can tell from the start that these sheets don't fit in the button well because they're too big.I went ahead a tried a few to see if I could get them to work, and the following images are the result. because the mylar was too big, the edges didn't seal completely. I was able to trim each one down by hand around the circumference to make them work, but it was very tedious and I will not be doing that for all 100 sheets.
Roberta Ebron
Reviewed in the United States on September 5, 2024
Just wrong size
Amy F.
Reviewed in the United States on August 12, 2024
absolutely perfect will buy again
Cassandra Clair
Reviewed in the United States on June 21, 2024
It hard to fix and metal backs in this size and my button machine doesn't work with plastic. These are sturdy and look fantastic upon completion. I have purchased this product from them twice. Quality appears consistent. Would recommend.
Mechabro Nine
Reviewed in the United States on December 28, 2024
1. The front and back don't fit together.2. The back is extremely thin and bends too easily.3. For some reason, about 1/3rd of the lip around the back often gets blown out in the opposite direction. I have to be VERY precise with my pressure to avoid this.4. Mylar films are too big. I had to trim some of them to fit.Overall junk product, avoid it. 0/100.
Sandra
Reviewed in Canada on December 27, 2024
Works lovely. My button has lasted a long time on a well used back pack. The pin can come off if the metal is not bent down. Some user error as you are learning.
N
Reviewed in Canada on November 9, 2024
Decent quality. I like how comfy they are to close, and the backing is good. I think the clear film should be cut a little smaller, and the main metal button piece was a bit large for the machine. Most of the pins I made turned out very nicely, so I think this is a good product.
Adam Bear
Reviewed in the United States on May 8, 2023
im always afraid that sizes will be wrong, but this was perfect! 44mm which fits 1.75 or 1.73in button machines, and comes with the adapter gasket as well!! WILL be buying again!
Jacklynn
Reviewed in Canada on May 29, 2023
The bottom part of the button with the pin is slightly too long and it pokes through the top creating a noticeable bump on them all sadly
Efstathios (Steven) Frangoulis
Reviewed in Canada on May 20, 2023
That the pins are exactly as I expected and are the right material
nad035
Reviewed in Canada on May 14, 2023
Fait très bien le travail à prix accessible
Eddie Suazo
Reviewed in the United States on March 15, 2023
Works perfectly with my 44mm chi button maker. My only regret is I didn't notice the back pin on these align to the middle and the ones that come with the chi button maker are more towards the top than the center. This is only a concern though if you have premade packaging that you need to adjust the alignment like I had to.
tlg
Reviewed in the United States on October 11, 2023
I use the 32mm buttons and they are better than any other button I’ve ordered on Amazon and I order hundreds and hundreds at a time.These are so thin and flat and look so much nicer finished. Other brands/styles are raised causing your paper to pinch and the buttons to look puffy.They are easier to make and there are no flaws or mis-presses. They cost a few more cents per button but the quality is worth it. I will be ordering these from now on.
Recommended Products