• Frame Size: 57 x 57 x 76 mm
• Body Length: 76mm
• Number of Leads: 4
• Weight: 1.1kg
• Single shaft is 8mm diameter,21mm length

* Motor Type: Hybrid

* Step Angle: 1.8 degree

* Holding Torque: 1.8Nm (270oz.in) 18kg.cm

* Phase Resistance: 1ohms

* Rated Current/phase: 3A

* Inductance:3.5mH+/-20%(1KHz)

* Frame Size: 57x57x76 mm

* Phase: 2 phase

* Insulation class: B

• Stepper motor's red wire connect to driver's A+ port
• Stepper motor's green wire connect to driver's A- port
• Stepper motor's yellow wire connect to driver's B+ port
• Stepper motor's blue wire connect to driver's B- port

• It adopts the common anode input mode, there are two input terminals, the wiring is more convenient;
• The working voltage is DC 10V-45V. recommended DC 24V;
• Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
• Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
• The rated maximum output reaches: ±4.5A.The output current is steplessly adjustable.

Subdivision

• full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.
• Automatic half-flow function
• Adopt enlarged radiator, good heat dissipation
• With output short-circuit protection function.

Wirings between driver & mach3 board (for example X-axis):

Driver's "CLK-" connects to control card's XP pin

Driver's "CW-" connects to control card's XD pin

Driver's "5V" connects to control card's 5V pin

Note:

The power supply cannot be connected reversely, otherwise the chip will be burnt out.

The set current should not exceed the rated current of the motor.

• Support for 4 Axis linkage, you can connect four stepper motor drives or servo drives;
• Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;
• Have 0-10V signal output,you can use mach3 software to control the spindle motor speed.
• One status LED, indicate connection status on the board.

• Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.
• Support for connecting electronic handwheel;
• MCU model: three generation 32-bit STM processor
• Communication plug-in: RnR motion control card - ECO-2.0

• 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.
• 4 general-purpose inputs, you can connect the limit switch, estop switch, probe , back to zero and other device.

• DC output voltage: 24V
• Output current: 0-14.5A
• Inlet stability: ±0.5%
• Load stability: ±0.5%
• DC voltage of Adjustable range: ±10%
• AC input voltage range: 110V-120V AC or 220V-240V AC; 115VAC/6.5A/50HZ or 230VAC/3.4A/60HZ; Selected by side switch.

• Working Temperature: -10℃～+50℃
• Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
• Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
• Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ

• Four fold protection settings, multiple protections, stable performance, effectively reducing the impact of AC input.
• Dual ball cooling fan and all metal casing design
• It has the characteristics of fast speed and good performance, which can ensure the temperature operation of the equipment and extend its service life.
• The shell is made of aluminum alloy and has a high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.
• Short circuit protection: when the output terminal is short circuited, the power is turned off and the output voltage is 0V.
• Overcurrent protection: when the output current is>115-150%, the output voltage is turned off.
• Overload protection: power protection when the load power is greater than 105-135% of the rated power.
• Temperature protection: the power supply is automatically protected under high temperatures.