Your cart is empty.
Your cart is empty.Product Description
Valve C Clamp Spring Compressor Kit
Feature:
This Valve Spring Compressor is used to easily and safely compress valve springs for removal or installation
The Spring Compressor set includes 5 collet sizes for correct and safe fit with almost any automotive or small engine valve spring and cylinder head
Everything needed to remove or install valve springs is contained in the set, including the wide C-Clamp, Pusher, and extension screws
Made of The forged steel construction of this set provides superior strength and hardness.
Suitable for motorcycles, ATVs, cars, and other small engines
Package Includes:
1 x Spring Compressor "C" Clamp: 16 x 19cm/6.3" x 7.5"
5 x Adaptors: 16mm, 19mm, 23mm, 25mm & 30mm
3 x Extension Screws: 11.3cm/4.4",11.3cm/4.4", 7cm/3"
1 x Compression Bar:10cm/4"
Spring Compressor "C" Clamp
This C-Clamp will not bend or twist under the stress of compressing valve springs. The smooth surface is finished with oxide to resist rust and corrosion
Adaptors
Suitable for a wide range of vehicles.
Pusher
The rods' fine threading is carefully engineered to take pressure evenly, while high-density carbon steel prevents wear
Easy to use
Close the coil spring compressor until touching the center rod, and insert the compressor into the coil spring. Carefully compress the spring for removal or install and only release compression when the spring is set for install. Handle with caution
Andrew C
Reviewed in the United States on September 24, 2024
I used this to compress and change out springs on my 2002 Audi A4 Quattro 1.8T engine. This had the right size ends to compress the springs and did it easier and more controlled than the type with the squeeze handle. I originally bought the large spring compressor from Harbor Freight but it was too big for my exhaust springs and was difficult to use. This was a little time consuming but worked perfectly.The built quality is a little cheap, the ends are a little loose when you attach them but they have nice big openings on the side so you can get out your valve spring retainers/keepers.Good value for the money and made the job as painless as it could be. I would recommend this to a friend.
john m isom
Reviewed in the United States on September 13, 2024
It works fine
CARLOS
Reviewed in the United States on August 12, 2024
I just did a valve job on a 5.4 32 valve engine heads and This tool made my job easier than I expected. Very easy and precise. Recommend and proven to be effective.
JWalker1970
Reviewed in the United States on March 11, 2024
This tool worked very well to compress my valve springs. I struggled with several valve compressor tools I had for over an hour with no luck and tons of frustration. They were too big to compress the small spring of the 1.6L (Ford Fiesta). I used the 25mm or 1" adapter. This new tool took me 5 minutes for the 1st one and about two minutes each thereafter to compress the springs and install keepers. Best of all it was stress free! I did however use a 5/16" stove bolt and thin fender washer to secure the valve in place through the spark plug hole. It did not interfere with this tool and made the process a little easier. (I had this installed before I even got this tool, and didn't need to remove it. This looks like it would work with any head design and valve spring of any size up to 1-1/4" in diameter. 5/5 stars
NESTOR BALDELOMAR
Reviewed in the United States on January 31, 2024
Es fácil de usar
El chido
Reviewed in the United States on April 30, 2024
This what i needed, i used it on a 07 mini cooper s, this item just perfect for the job very easy to use.Thanks.
Larry C.
Reviewed in the United States on April 12, 2023
Worked as expected a little bit flimsy but did the job would recommend it
David B.
Reviewed in the United States on April 29, 2022
The threaded rods would not pass through the C clamp completely. Needed to rethread the C clamp with M12 x 1.75 tap. Otherwise it worked for my application.
Recommended Products
$28.99
$ 14 .99 $14.99