Your cart is empty.
Your cart is empty.This chisel is made by a small tool manufacturer in the Czech Republic and is of exceptional quality. The blade is made from fine-grained, nicely tempered chrome-manganese steel and hardened to Rc 59. The blade will take and hold an excellent edge. The blade is accurately ground and has a slimmer cross section that woodworkers prefer. As with all fine edge tool, it will need sharpening/honing before use. This chisels is an excellent value in a good quality tool. This blade is 50 mm (2 inches) wide and is 6 1/2 inches long. The handle is made from super hard European Hornbeam and is 5 1/2 inches long. Overall length is 12 inches. Bevel is ground at a 25 degree bevel. The blade has a well-seated heavy steel tang and the handle has a brass ferrule to withstand vigorous mallet work.
Two thumbs up for my papa bear shorts, thanks
Reviewed in Canada on November 10, 2024
It’s a thing of beautyI’d get two if I could afford it
Jimmy
Reviewed in the United States on March 16, 2023
Worked really well for me right out of the packaging. Will do some typical chisel tweaking but no complaints about the quality. The steel is great, the balance is good, and the hornbeam handle feels really nice in the hand. I didn’t expect to be so impressed by this chisel but I was. I do suggest smoothing out the sides of the blade as they are a bit too sharp and could cut you while in use.
J Carter
Reviewed in the United States on May 11, 2021
I am some what conflicted in my feelings about this chisel. Of course it needs sharpening and back flattened. Here is where the first problem arose, it took a long time to dress bottom of this chisel, a long time, mostly I supposed due to its width. Once chisel was sharp I set about using to deepen cut lines for housing groove. This is where problem two came up, edge of chisel was fracturing, resharpened and tried again , same results. After third attempt raised angle a couple degrees, not as bad now. One more time and it seems okay for now. Overall this will work for its intended purpose I think, I did tests in pine. I like having wide chisel for this purpose, for me it makes staying on line easier ( failing eye sight) and doesn't move wall if done correctly. The handle is big and ugly in my opinion but doesn't effect performance. Sides are well ground with fairly thin edges, if that matters. For the price this is a good deal if it can hold an edge.
Scott D Anderson
Reviewed in the United States on April 19, 2021
Very sturdy, nice steel, obviously needs to be sharpened.Take the coating off it first, then sharpen as normal. Not hard to get razor sharp, and the edge stays pretty well so far.I've used this instead of a shoulder plane (I don't have one) and it works great.
Jarl Seamus
Reviewed in the United States on June 27, 2020
I must admit I wasn't expecting much from an inexpensive chisel, and anticipated doing a LOT of work to it to get it up to speed, but this guy was in terrific shape right out of the box. It had a fantastic finish on it, nearly polished, the back was flat and the edge was square, consistently ground, and nearly sharp straight from the factory. It took me about 10 minutes to final sharpen it and dress the bevel. The handle wood is tight, well shaped, and free of defects. It feels comfortable in the hand and performed some test cuts flawlessly. We shall see about edge retention soon, but even if it is a bit soft, I generally am very gentle on my chisels so I think it will be a welcome addition to my chest of tools. In short, this is a fantastic slick and for under $30 it's a real gem.
Customer
Reviewed in the United States on June 27, 2020
Excellent quality once you flatten and sharpen. Be wary right out of the box. The machined edges have an almost serrated quality and will slice you up. I cut the crap out of my finger on the side testing the factory edge.
maisonlumier
Reviewed in the United States on July 3, 2018
great item well made for the price you can not beat it and then some.Needs some work to fine tune, not much.They all need fine tuning.
Jason
Reviewed in the United States on April 13, 2017
I'm happy with the quality of steel for the price, and it holds an edge ok. But it's was way out of flat and after about an hour between a diamond stone and a glass stone, I finally got the top 1/3 of the back flat, and the bevel took an edge pretty quick. However, not many tool makers are building large timber chisels that are shop worthy anymore, so overall, I'm happy with my purchase. If you're used to Lie-Nielsen or Veritas tools, you'll need to get used to a lot of setup work before you'll be ready to get paring shavings.
Blaine
Reviewed in the United States on December 20, 2016
I have yet to get my hands on a poor quality product from these guys. I am not a professional and get that these are not professional grade. But I am a ridiculously happy customer that owns a complete set of Narex chisels and will continue to buy them. Very keen edges. Hard steel. Flat. Great angles that make sharpening a breeze. Precise lines. Just a pleasure to work with.If I had one complaint. I would very much like to see a metal cap on the end for mallets. I feel that eventually the wood will get mushy.
Recommended Products
$118.00
$ 56 .99 $56.99