Your cart is empty.
Your cart is empty.It is the customers responsibility to make sure that this is the correct part for their unit. New vertical 7/8" shaft pressure washer water pump for many different makes and models. SPECS: 7/8" shaft, aluminum head, 2800 PSI, 2.3 GPM, Includes thermal release valve, chemical injector, garden hose hookup (22mm outlet), pump oil already installed, 1 year warranty against manufacturer defects. If you are not sure if this is the correct pump for your unit please send us model number off your machine and we will gladly check for you. PLEASE NOTE: Spacers may be required for installation depending on motor configuration. Spacers are used in the case that the pump arm(s) hits the engine. Pump may require longer mounting bolts due to its thicker flange, for added strength.
WILLIAM MARTIN
Reviewed in the United States on November 20, 2023
I had to put washers between the legs of the pump and the bottom of the base of the washer to get it to tighten. Also for the price of the pump which is $25 more than others on Amazon they don't supply any hardware. So you better keep your old bolts and nuts oh and the key stock for the motor shaft because they give you nothing.
Gayle T
Reviewed in the United States on September 12, 2020
Installation was slightly more difficult than it should have been b/c i had just filled up the gas tank, and didn't want to drain so I could lay on it side/upside down to install. But, it was generally easy overall.When I first fired up the engine and squeezed, the motor had some serious vibrations. It would bog down quite a bit - almost to the point of stalling a couple of times. I eased up on the trigger and let the motor catch up. Rinse and repeat a few times and then it starting running smoothly with solid pressure. I guess it needed a slight break-in period.I don't use the washer that often - so hopefully this will have a good 10 year life as well.
Galaxy owner
Reviewed in the United States on August 1, 2020
I ordered from another source but it didn't have the bolt pattern so I got on Amazon and found this one with the right bolt pattern and it bolted right up. It works great. The first one said it would fit the troy bilt pressure washer, I even had the number off the old pump and campared the numbers to the new one but it didn't fit.
Helen A O'Donnell
Reviewed in the United States on July 20, 2020
The product was exactly as described. The hole spacing fit my Troy-Bilt power washer perfectly, though I did have to add some lock nuts as spacers. Builds and maintains pressure like a new washer. Four stars instead of five until I see how long it lasts, but I recommend it as a replacement pump.UPDATE: Four years later the pump is still going strong. Five stars!
tonya
Reviewed in the United States on June 27, 2020
Broken with first use. Pump lost low pressure for soap half way thru house wash.
Donald Betsinger
Reviewed in the United States on December 13, 2019
I loved the way it fit on my 18 year old pressure washer. Just make sure you know the bolt pattern, and shaft size. And this is easy. Takes about 5 minutes to install, with one more set of hands, to hold the engine in place. Good job
Customer
Reviewed in the United States on August 22, 2018
Pump is fine but I had to put spacers in to make it work on briggs as the oil drain plug caused it not to bolt up.
DAVID E. SIMPSON
Reviewed in the United States on February 14, 2018
Arrived well packed. Installation was easy but did require the 1/2 inch steel spacers. The spacers are needed because the motor shaft hole in the original pump is deeper than the hole on the replacement pump. The bolts were still long enough. The motor on my pressure washer is a Honda. You will need a 13MM open end wrench and a 6MM hex wrench. Be careful when you have the pump removed because the same bolts hold the motor to the frame and it could fall off. You need the open end wrench because only one of the nuts is accessible with a ratchet. Will be a couple weeks before I can try out the pump but I don't expect any problems.
Recommended Products
