Your cart is empty.
Your cart is empty.Product Description
O'SKOOL Miter Slot Runner Slider Bars for Table Saw Miter Bar, Crosscut Sled, 430mm, 2 Sets
Contents included: (2 )Miter Bars, (12) #8 wood screws (3/4| long), (8) 1/4"-20 UNC countersunk machine screws, (1) 2.5mm Allen key wrench, (1)instruction manual
Easy insertion
The roundover design allows for easy entry into the miter slot.
Zero clearance
The expansion collars ensure zero clearance between the miter bar and track, preventing any wiggling for enhanced accuracy.
Premium aluminum alloy
Crafted from premium aluminum alloy, these miter bars offer exceptional durability.
Sco Mo
Reviewed in Canada on March 7, 2025
These guides fit my Dewalt contractor saw and needed very little adjustment of a snug fit. I used double sided tape to adhere them to the base of the jig so that I could properly locate them and then screwed them into place. The price was reasonable and they do the job.
mr j friel
Reviewed in the United Kingdom on March 4, 2025
They're pretty good for the money. Not precise in my Rutlands table saw but you can adjust them to make fairly accurate cuts
Steven R.
Reviewed in the United States on February 8, 2025
I used a pair of these for a small crosscut sled on my Sawstop table saw. They fit the slots perfectly and slide nicely. It should be noted that the tightness adjustment Allen screws for the bars are on the top, in case that's an issue for your particular use. My sled has no bottom piece so that two of the adjusters are easily accessible and two are not, but I haven't needed to make any further adjustments since it was built. I think the quality is very good and the cost is reasonable.
Jimmie
Reviewed in Canada on February 7, 2025
Don’t waste your time or money on anything else. Very impressed with this product. Ill buy again!!
Customer
Reviewed in Canada on February 7, 2025
Great quality
Marvin E Lanning
Reviewed in the United States on February 3, 2025
Works great.
Customer
Reviewed in the United Kingdom on April 17, 2025
Lovely quality
M. Fischer
Reviewed in the United States on April 10, 2025
I purchased these rails for a crosscut sled for my DeWalt table saw. Overall these are a great improvement over my previous plastic rails. The rails fit well into the miter slots and the captive washer at the end of rail helps retain the sled in the T miter slot.The installations instructions were marginal at best. Firstly, there should be two templates provided as the location/drilling guide. There are two rails; hence one template per rail. Secondly, the instructions could me marked more clearly to properly identify the holes and their specific purpose (i.e: top screws vs. bottom screws). I made a few mistakes that I recovered from but clarity in the instructions would have helped.The build quality is excellent and the end result functions very well for my crosscut sled purpose. While more expensive than simple plastic rails, these are a higher quality and worth the extra cost.
Jeff
Reviewed in the United States on September 11, 2024
The length of the miter bar is good for a mid size table saw crosscut sled. It ensures for the most part, all 4 rubber grommets are in contact with the miter slot, which offers the zero play. The rounded nose is definitely an excellent design. it's easy to put in the miter slot. the rear end should also have a retention disc like the front end. Even it comes with the scheme paper, I still find it difficult to align. Adjusting the rubber grommet from the top is a good idea. but aligning the hole to the exact location grommets is hard.
romarosie
Reviewed in the United States on December 7, 2024
If you're like me, you've probably built a ton of job specific sleds for your table saw or router. The one piece of the equation which can be irritatingly time consuming is the guides. This little device makes quick work of that, and works the business, as you can firm up the adjustment fairly easily for greater accuracy of your cuts.Since I've received it, I've been looking for a reason to do just this, but haven't come on an opportunity to put these to use. Hence no photos of them in operation. Fortunately or unfortunately, I haven't needed to yet. But that's not an indicator of how neat these are, as I can't wait to use them. They fit my saw perfectly and I'm 100% confident that when the time comes, these are going to be the business. Very satisfied with the product.
Tracy F
Reviewed in the United States on December 10, 2024
These have helped with woodworking something fierce. Have went back and bought other variations.
John
Reviewed in the United States on November 2, 2024
Why would you put the adjustment washers on the top side where it’s going to be screwed into a piece of wood. This means that you’ll have to unscrew the rails from the board anytime you need to adjust the play.As a machinisf and woodworker this design doesn’t make any sense, and frankly it’s embarrassing.All of the adjustment capabilities should be on the bottom/ accessible once the rails are fastened.
josh schmidt
Reviewed in the United States on November 19, 2024
This is a solid product, purchased to use on a rip sled (crosscut sled) for cabinets. They were easy to adjust so there is no slop and easy to install. I like the washer which locks it down in the T slot. Very happy with the purchase
Recommended Products
$15.99
$ 6 .99 $6.99