Shopping Cart

Your cart is empty.

Your cart is empty.

Thermal Adhesive Tape, 10mm x 25m (0.4in x 82ft) Double-Sided Thermal Tape, Non Conductive, for Heatsink LED Strip Mosfet SSD DDR GPU CPU PCB IC Chipset

4.3 (8) Write Review
Free shipping on orders over $29.99

$8.99

$ 3 .99 $3.99

In Stock

1.Size:5mm


About this item

  • Excellent Adhesion, Easy to Use: can effectively replace the grease, liquid glue fixation, improving the heat transfer between electronic components. Just paste it on, no curing time.
  • High Thermal Conductivity: Stable performance, Long-lasting adhesion on both sides, Can be tightly and firmly fit the heat source devices and heat sink, to achieve the effect of heat dissipation.Thermal tape with the Tensile resistance, softness, compression.
  • Ultra-thin film with insulation and non-conductive, Low cost solution for many application. Long term heat resistance: 120 ℃; Short term heat resistance: 180 ℃; Thermal Conductivity:1.6w/m-K; Adhesive power: 1.3kg/inch; Breakdown Voltage:4kv; Size: 10mm x 25m or 0.4inch x 82ft (W x L), Thickness: 0.25mm
  • Wide Range of Use: Thermal Tape applies to Heatsink, CPU, GPU, HDD, IGBT, High Power LED, LED Strips, Laptop, PCB, Video Card RAM, MOS Tube, 3D printer, Circuit Board, DDR Memory Modules, SSD Drives, Power Semiconductors, etc.
  • Package lncluded: 1 Roll 10mm x 25m Double Sided Thermal Adhesive Tape.


Product Description

Used for attaching heatsinks to CPU GPU,high power LED,Video Card , RAM, DDR Memory Modules and other power Semiconductors.

DRTAPE 01

Ultra-thin film with excellent insulation , Low cost solution for many application

DR

Temp:

Long term heat resistance: 120 degrees Celsius

Short term heat resistance: 180 degrees Celsius

Thermal Conductivity:1.3w/m-K

Adhesive power: 1.3kg/inch

Breakdown Voltage:4kv

dr025

Color: White

Thickness: 0.25mm

Length : 25M

Width: 5mm, 8mm, 10mm, 15mm, 20mm, 22mm, 25mm, 30mm, 40mm, 45mm, 50mm optional


djk123
Reviewed in the United States on August 10, 2024
Plug and play for TPM on the motherboard. Recognized and functional
Customer
Reviewed in the United States on March 27, 2023
Seems to hold my small heatsinks to my stepper drivers well… I haven’t tested it on anything else yet.
Customer
Reviewed in the United States on May 20, 2022
I was trying to replace a small heatsink on my GPU's memory chip only to discover the tape wouldn't stick to anything. Not a fun discovery mid repair.
mike ratliff
Reviewed in the United States on August 24, 2016
Great stuff a bit too sticky on somethings but still a good product for sticking heat-sinks on raspberry pi
Chris C.
Reviewed in the United States on August 10, 2016
Wasn't the easiest to install, but still worked well enough for a 4-star rating. The tape "cover" wasn't the easiest to remove, and took some working to remove it without unsticking it from the chips. Once on though, it held heatsinks on well enough.
Bloodloss
Reviewed in the United States on June 9, 2016
Easy to use and well packaged. Makes applying a heatsink compound as simple as possible.
Matthew Shultz
Reviewed in the United States on May 17, 2016
Used this to mount some heatsinks to my cable modem PCB. Worked great and seems to be conducting heat well.
D. Bailey
Reviewed in the United States on October 27, 2016
seems to do fine thermally, but it doesn't have very strong adhesion. tried to use to to put DDR4 heat spreaders back on after removing a waterblock and it works, but it is very easy to knock the spreaders back off. about as much sticking power as scotch tape.